Switches are available in different types. To independently connect the model in the apartment, it is important to know the circuit diagram of the switch. Additionally, the connection box device must be taken into account .
There are blocks for two or more contacts. To check the phase on the plate, a tester is always used. Additionally, a screwdriver will be required during operation. Modern switches are made with double-sided clamps, which are very firmly fixed. In order to understand the issue in detail, it is recommended to consider connection schemes.
Connecting a device with a channel adapter
The wiring diagram for the switch with a channel adapter has one contactor. Blocks in this case can be on two or more contacts. If we consider a one-button model, then the connection is through a trigger with clamps. The overlay is installed first. Then it remains only to connect the lower and upper contacts.
Latitude Adapter Models
The switch connection diagram implies the use of a single connection block. The trigger in this case is required for two contacts. First of all, the switch plate is installed. Then, using the screwdriver, the controller clamp plate is removed. At this point, it is important not to touch the contactor. After that, the upper conductors are connected in the first phase. The resistance at the contactor should be exactly 10 ohms. Additionally, check the clamping plate. It must fit snugly against the block.
Double Box Switches
A dual-box switch wiring diagram includes a wired adapter. The trigger in this case is used low impedance type. If we consider the switch (switch) for one key, then the controller must be selected for three outputs. The upper contacts are brought under the first phase. Also, the switch connection circuit has an expander. The pad is in contact with the unit.
At this point, the switch cover is immediately removed. The unit screws must be tightened very carefully. Phase zero is checked by the tester. If we consider the switch on two keys, then the trigger is used on four outputs. The upper contacts are connected in the second phase. The switch controller must be padded. It is also important to note that the trigger must be located under the contactor. Its overlay is fixed on the connecting block. The lower contacts of the switch are brought in a zero phase. The contactor resistance must be at least 12 ohms.
Installation instructions for the model on two latches
Two latch devices are connected via a conventional controller. The connection block can be used on two or three outputs. If we consider the first option, then the trigger is used duplex type. The installation of the switch begins with the fact that the upper contacts of the element are connected in the first phase. The resistance of the device must be at least 10 ohms. The lower contacts must be connected in the zero phase. In this case, grounding is installed with an insulator. The controller must be fixed with an overlay. The clamps are secured with a screwdriver. When shifting the switch, the plate needs to be adjusted.
Connecting a device with four latches
Devices with four latches are fixed on plates of different thicknesses. If we consider the standard connecting block, then the controller is allowed to use two outputs. Phase zero is checked using a tester. The expander is connected with a filter. Insulation is installed last. It should also be noted that one-key models are connected through an expander.
Wire colors need to be determined in advance. The upper blue contacts are connected in the first phase. The locking plate must be well tightened. For this, a prepared screwdriver is used. The lower contacts are connected in the second phase. If we consider the connecting block with the contactor, then two insulators will be required to install the switch. Pads can be used with different conductivity.
Integrated Contactor Models
The connection diagram of the switch with integrated contactors provides for two triggers. Models on one or several exits are used. If we talk about switches with one key, then the upper contacts are brought in the zero phase. The resistance is at the level of 12 ohms. The colors of the wires must be determined immediately. The lower red contacts are allowed to be connected in the first phase. The expander closes on the plate. Isolation for the controller is installed last. It is also worth noting that it is important to carefully tighten the plate with a screwdriver.
Connecting a device with two-digit contactors
Switches of this type can be installed in connecting blocks with triggers. If we consider a circuit with two outputs, then the upper contacts are closed in the zero phase. The resistance should be approximately 12 ohms. If we talk about models with two outputs, then insulation is installed first. The upper contacts are always in phase zero. The expander must be firmly clamped under the plate. The lower contacts are connected in the first phase. The resistance in this case must be 10 ohms. Considering the connecting blocks with triggers, it is worth noting that grounding is used with the controller.
Devices of the MV2 series
The circuit breaker connection scheme for this series includes the most common closing mechanism. In this case, the box is used in three phases. At the same time, the switches are suitable for her only two-pole. Directly, the installation process of the circuit breaker begins with checking the integrity of the cover. Next, it is important to close the block. To do this, the clamping mechanisms move apart on the sides. If we consider the model with two latches, then the block should first be mounted on the upper side. After installing it, it is important to check the first phase.
If the negative resistance is within the normal range, then you can proceed to the connection of the conductor. To do this, the clamp is screwed with a screwdriver. Next, it is important to check the strength of the box. The plate in this case does not need to be bent. The ground contact can be shifted to the side so that it does not come into contact with the adapter. At the end of the work, the top cover with buttons is standardly fastened, and after that the model can be checked for operability. This switch costs (market price) about 110 rubles.
Switches of this series are installed through wire blocks. Triggers for modification are suitable for two and three outputs. It should also be noted that when connecting the switch, the resistance is checked. The specified parameter is 10 ohms. The upper contacts of the model must be closed in zero phase. The plate is clamped to the switch only after insulation of the wiring.
The lower contacts are connected in the second phase. To check the voltage on the unit, a tester is used. When a spark occurs, the contactor immediately switches off. If the controller is not installed correctly, the two-key switch may be short. It should also be noted that when installing the model it is important to monitor the insulation of the clamping plates.
Connection of KV1 models
The switches of this series are installed in connecting blocks on two outputs. As a rule, the model fits on the pad. The isolator at the switch is used with a trigger. If we consider a two-key switch with a block for two outputs, then the trigger must be closed on the plate.
The upper contacts are connected in the first phase. It should also be noted that the controller is installed behind the insulation. In some cases, problems may arise with fixing the expander. In this case, you need a small screwdriver. The plate is clamped last. When installing the switch, it is important to monitor the position of the cover. The lower contacts are always connected in the second phase.
These switches are installed in the junction box on two contacts. Controllers can be used expansion type. When connecting, experts advise you to immediately determine the zero phase. The top pins are clamped first. It should also be noted that the pad must be centered.
The insulation of these switches is wound. The lower contacts are connected in the second phase. If we consider a circuit for two controllers, then the contactor must be used with a latch. The lower contacts of the switch are closed in the first phase. To check the voltage, you can use the tester.