If you are thinking about building a bathhouse in your suburban area, you are on the right track. Indeed, with frequent exposure to its beneficial properties, immunity is significantly strengthened, mood is improved, the whole body is healed. However, in order for the bathhouse to really give a result, even in the early stages it is necessary to take care of the design and location of the bathhouse furnace. After all, if improperly placed, the maximum air temperature will be no more than 80 degrees Celsius. So, let's look at how to make a bath stove with your own hands.
Drawings - this is the first step, on the correctness of which all the characteristics and design of the room will depend. However, even before the development of the drawing, you need to decide which type of boiler you will use. Below we will consider several types of these devices and note their features.
There are currently two main types of bath stoves:
- With an open heater.
- With a closed heater.
Devices with an open heater
A similar type of heating tool is used in cases where there is a need for heating the room for several people. Thanks to its special design, an open-hearth oven can quickly heat a steam room to more than 100 degrees Celsius. However, at the same time, due to the high concentration of water, it cools very quickly. Therefore, it can be used no more than once a day.
In this case, the stones in such a stove are laid in bulk on the firebox. And so that the device does not quickly cool down and at the same time has good heat dissipation, after each treatment of stones with water, carefully cover them with a screen cover.
The design of this heating tool also includes a chimney, which is often made of a 1.5 mm layer of tin steel. In this case, the lower pipe (if it is a home-made furnace) can be made from an ordinary water pipe with a width of 15 centimeters. The length of this device should be about 150 centimeters. In addition, a damper is additionally put on the nozzle.
Thus, the design of the furnace with an open damper includes not only a tank for loading a certain type of fuel, but also a pipe together with stones. By the way, stones should be used only of a special type, designed specifically for use in such conditions. It is simply unreasonable to use a regular cinder block or brick, since they do not have good heat transfer at all and cool very quickly. Therefore, stones should be bought only those that are specifically suitable for the bath. Spread them in the oven as follows: put stones wider in size below, and pour small ones on top. Thus, you will realize the most efficient heat transfer from the furnace, which means that the steam room will be heated in a matter of minutes. Up to 100 kilograms of stones should be put in brick bath stoves, while the temperature of the top (respectively, the smallest layer) should be at least 300-350 degrees Celsius.
Of course, the stones warmed to the limit are somewhat alarming - will the wooden bath light up at this temperature? As practice shows, this does not happen. But if you want to make your bath more fireproof, you can install an additional layer of asbestos cement insulation. It is carried out exclusively on the ceiling. In this case, the chimney is discharged 50-60 centimeters above the ridge of the bathhouse. An additional protective cap should be installed above the pipe, which will prevent the ingress of various precipitation into the system. The bottom of the chimney can be closed with a tin plug.
The design of this furnace does not fundamentally differ from the above option. The only differences are the availability of a special niche for loading hot stones. And in order for the formed steam to go outside, a special door is also mounted on such a device, which is placed on the same level with the top layer of small stones. When the sauna stove is working, smoke gradually leaves the chimney, and fumes leaking from the surface of the fuel doused with water seep through the door. After turning it off, the heat will remain in the bath for about a couple of days. Of course, you cannot use such a stove the next day (you need to wait until it cools down).
In principle, the most suitable option for a home bath would be to install a device with an open heater. But since their design has a lot of similar details, the installation instructions below will be suitable for a stove with both an open and a closed heater.
A stove with a closed heater, as a rule, can be either long-term (permanent), or periodic action.
So, how to make a sauna stove with your own hands?
First, we need to prepare a set of tools and devices with which we will install this furnace. In the course of the work we will need:
- Gravel for the construction of the foundation.
- Clay to obtain a solution.
- Waterproofing elements, such as tar and roofing material.
- Capacity for solution (if it will be a bath furnace with a tank).
- Squares, doors and other construction details.
We will indicate all other tools in the course of our story (as a rule, almost everyone has such devices in the garage or in the country).
How are brick bath stoves mounted? First, before installation, determine the place where this device will stand. Typically, a gas bath stove is installed in the corner of the room. This will significantly save free space and make the device more convenient to use. You must admit that every time it is unpleasant to go around a container with stones heated up to 350 degrees Celsius, if it is placed in the center. Although, undoubtedly, the level of heat transfer in this case is the most uniform.
If it’s a brick-built stove built with your own hands, handle it carefully and it is advisable to think over its future design in advance. By the way, the foundation for this tool needs to be done separately from the foundation of the bathhouse itself. To do this, dig a pit below the freezing boundary of the earth (this is about 80-90 centimeters in depth) and cover its bottom with wet sand with a layer of 15 centimeters. After that, beaten bricks and stones (not saunas) are poured into the same pit. All this should cover the foundation pit another 20 centimeters up. Well, at the final stage, all this is covered with a layer of rubble. After the formwork is done, the area and dimensions of the future used furnace are limited with the help of a reinforced frame, and from above all this is poured with concrete. Everything, after 3 days (until the cement hardens), our foundation will be ready for use.
But do not think that at this stage the do-it-yourself sauna stove has been successfully installed. There are many more things to do. First of all, it is necessary to remove the formwork, and while the concrete will dry out, you can go to the store and purchase additional construction materials if necessary. After the foundation hardens, it is then treated with a layer of roofing material and tar, after which the remaining gaps between the soil and concrete are covered with gravel or coarse sand.
Now sand-clay mortar is mixed for laying bricks. Clay with water should be combined by mixing both substances in one container, gradually adding sand there in a ratio of 1 to 1. The finished mixture should be homogeneous and resemble a light gray color. By consistency, such a substance is similar to sour cream.
DIY sauna stove installation - bricklaying
And now the fun begins - the process of laying brick. First, the feather bedding is done (on a waterproofing pad), then secondary according to the standard scheme, taking into account right angles. Approximately in the third row, leave room for a blower and strengthen it with steel strips. On the next row is a well for the grate. But that is not all. Approximately on the 7th row, the placement of the furnace door ends with the well itself. A tank for hot water is placed on the 14th layer of bricks, on the 23rd - the installation of the pipe begins.
At the final stage, the appearance of the resulting device is completed - a brick wall is plastered with a small layer of asbestos.