In order not to waste time searching for tools (hammers, screwdrivers, wire cutters), they should be stored in one place. But what if all the racks and cabinets in the house are full? An excellent solution to this problem will be a homemade tool box. You are not required to have special knowledge and skills. The process of manufacturing a portable box will take no more than 3-4 hours.
Where to start?
The first thing you should decide is the size of the box. It all depends on the size, quantity and total weight of the tools that will be stored in it. As for the configuration, it does not really matter. The finished product may have a square, rectangular and any other shape. As you wish.
Homemade tool box is usually made of lumber or artificial wood (OSB-plate, plywood sheet, chipboard). Often, various metals and high-strength plastic are used. It is difficult for beginners to work with these materials. Therefore, they prefer wood.
How to make a tool box : expert advice
If you do not want to make serious mistakes and waste time, then listen to the recommendations below. Only in this case can we count on a good result.
1. To make a convenient and reliable tool box with your own hands, you must first draw up a design drawing. This is done taking into account the type, quantity and total weight of the instruments.
2. Typically, the boxes are made of boards used previously in other designs. Before re-use, they are cleaned of dirt and dust. For light tools it is better to take plywood, and for heavy ones - strong boards.
3. On wooden surfaces are marked out all the details of the box. Next, we cut the workpieces using a jigsaw or a saw with small teeth.
4. Do you want to make an open tool box with your own hands? A similar design provides for a central handle. To install it, you need to drill 2 blind holes.
5. The assembly of parts is carried out using screws and screws. Securely fix the handle and glue all the seams.
6. Make a DIY tool box - only half the battle. It is also necessary to give it an attractive look. You can cover the surface of the box with paint or special varnish.
Tools and materials
Very soon we will begin the practical part, and for now we will prepare everything necessary. So, for work we need:
- drill;
- PVA glue;
- plywood (thickness 12 mm);
- file designed for wood jigsaw;
- hammer;
- jigsaw with sawing function at an angle of 45 degrees;
- varnish for wooden surfaces;
- drill;
- several bars 15x15 mm;
- clamps;
- small nails.
Do-it-yourself toolbox : step-by-step instruction
What should we end up with? A wooden structure where pliers, screwdrivers, a hammer and other tools will be stored in the future. The action plan is as follows:
Step number 1. First, pick up plywood. We will use it to make the side walls of the box. In order for the ends to fit together well, they need to be trimmed a little by placing the jigsaw file at an angle of 45 degrees. Specialists call this type of docking a "connection on a mustache."
Step number 2. We coat the ends with wood glue. If you were unable to buy it anywhere, then use PVA.
Step number 3. We begin to assemble the entire structure. So that the parts do not crumble, they need to be fixed with tape. Make sure the walls are connected evenly. Now we wait until our workpiece dries.
Step number 4. To the existing design, nail the slats that will hold the bottom of the box. Here you need to be careful, because the nails are very small.
Step number 5. We make the bottom of the box, and then glue it to the slats. We use the same PVA.
Step No. 6. For the convenience of carrying the box, we make a handle. Take a thin board. With a fret saw, we cut out the thinning on it. It is very important. Also remember to cut small rectangles from each corner of the handle. Their depth is equal to the thickness of the plywood from which the sidewalls are made.
Step number 7. In the side walls we drill and bore cutouts under the handle. Make sure nothing dangles. There should be blind holes in the sides of the handle and the walls of the box for inserting dowels.
Step number 8. We proceed to the assembly of the handle. All its joints with the sidewalls, as well as the sidewalls with the walls, are thoroughly coated with PVA. Gradually collect the handle parts. We fix its position with the help of clamps.
Step number 9. All that remains for us to make is a holder for the compass, chisels and screwdrivers. We will use plywood. Cut a strip from it, the width of which is 4-5 cm, and the length is equal to the inner size of the long wall of the box. Then we drill holes for the tools. Coat the strip with glue and attach to one of the walls using clamps. Once the glue is completely dry, you can begin to finish the surface of the box. For this purpose, varnish or paint is suitable.
Conclusion
Now you know how to make a tool box yourself. There is nothing complicated here. The main thing is to clearly follow the instructions described above. The materials from which the structure is created can be easily purchased at any hardware store.