How to make a boiler with your own hands from improvised means?

In the article we will talk about how to make a boiler with your own hands. Methods of manufacturing this simple device mass. But why do it? The stores have a huge selection of devices of various characteristics - both 12 V and 220 V, both small and large. But if there are no shops nearby, then there is access to a power outlet and you want to have a cup of invigorating tea? Then our article will be useful. However, it can also be used for experiments. But remember - all designs are dangerous. The risk of electric shock is extremely high.

Homemade boiler rating

The most proven ways to make a water boiler with your own hands:

1. Using matches and blades.
2. With the help of steel nails.
3. Using a heating element.
4. Of nichrome wire.
5. Of the resistors.

The main thing in the manufacture of a boiler with your own hands is to exclude the possibility of a short circuit. Use the device as carefully as possible.

Making a razor blade boiler

In order to make such a design, you will need the following elements:

• 2 blades.
• 2 matches.
• Threads.

The manufacturing procedure is simple, it can be divided into several steps:

1. Take a wire with a cross section of at least 0.75 mm ² .
2. Strip the ends of the wires and securely screw them to the blades.
3. Please note that the blades must not touch. To do this, set matches between them - they will fulfill the function of struts and protect against short circuit.
4. Tie the blades with threads so that they cannot move freely.

That's all, now you can try to make a seagull.

How to use a boiler?

Now you know how to make a boiler with your own hands. The design diagram is shown in the figure in the article. But you still need to be able to use it. The main requirement for the capacity in which boiling will be carried out is that it should not conduct electricity. Plastic or ceramic containers are suitable (the second is preferable). Care must also be taken when turning on and off. First, lower the device into water, then just plug it into the network. And when heated, do not touch the water, wire or container.

It is worth noting one point - you cannot heat distilled water in this way, since it does not contain metal salts that conduct current. And you are unlikely to like tea, since the electrolytic method has a bad effect on the taste of water.

Is there a heater?

The easiest way to make a boiler is from an electric heater. In addition, it is the safest design option. Such an element is available in various devices - in kettles, washing machines, dishwashers, coffee makers, etc. In order to make a boiler, you need to prepare the following elements:

1. TEN.
2. A wire with a plug.
3. Terminal blocks

Heater manufacturing algorithm:

1. Strip the wires from insulation with a knife.
2. Lead the wires into the terminals and fix them on the TEN terminals with screws.
3. Check the resistance of the heater coil with a multimeter.
4. Check for short to housing.

If the device has passed the diagnostics, then you can start operation. Such a boiler can be used without restrictions. Boiling water does not lose its taste, so it can be eaten. The amount of water that can be boiled depends on the power of the heating element.

We make a boiler of nails

In fact, this is an analog of the blade design discussed above. That's just the boiler turns out a little more complicated. For work you will need:

1. Nails 80 mm - 6 pcs.
2. Two-core copper wire and plug.
3. Electric drill and drill 3 mm.
4. Wooden board 10x10 cm, thickness 2.5 cm.

In order to make such a design, you need to adhere to the sequence:

1. At a distance of 3-5 mm, make 6 holes in a wooden plate with a drill.
2. Install the nails into the holes.
3. Divide the nails into two groups of 3 pieces and connect the wire strands to them.
4. Install a plate above the water tank, and plug in the power outlet.

Carefully make sure that the wires are pressed tightly against the nails. To do this, it is recommended to add about a third of the core thickness into each hole. Only after installing the nails. Before the first start, it is recommended to check the resistance between the contacts on the plug - it should be zero.

Device use:

1. Fill a non-metallic mug with water (as we mentioned earlier, distilled will not work).
2. Set the plate on top of the mug, the electrodes should be pointing down.
3. Plug in the 220 V device.
4. As soon as the water boils, you must disconnect the device from the network.

As you know, the water quality in this case will not be very good, you are unlikely to want to drink it. But for technical needs, it will do. Now you know how to quickly make a boiler with your own hands. Be careful when working with electric current, and make sure that at least somewhere there are areas with bare wires. And also do not allow children to use such devices.