If the furniture facades are uneven in relation to each other, it is striking. Such problems can arise for many reasons, so you should know how to adjust the cabinet doors. by yourself. Facade offsets come from factors such as:
- moving furniture to another place or at the time of moving;
- uneven floor effect;
- high humidity in the room;
- due to the long service life.
Before starting to repair furniture, you should pay attention to the moment the doors are skewed, maybe they are installed incorrectly. In some cases, the assembly of structures can be carried out in rooms where there is an uneven floor. To do this, you need to compare the size of the diagonals of the cabinet. If they do not match, this means that the design is broken. From this action will depend on how to adjust the cabinet doors of any type.
Advice
Before taking any action and thinking about how to adjust the cabinet doors, a thorough inspection is necessary. Only after completing this action will the cause and solution be known. If the gaps between the door panels of the cabinet are uneven, this means that the adjustment must be done by adjusting to the right or left. At the moment when the front panels do not close, because they hang much lower or are located above the opening, it is necessary to carry out vertical regulation. Cabinet door panels can have two types of device:
- in the opening of the frame;
- inside the opening.
Accordingly, the mounting options are different, that is, the loops themselves. But the methods of adjustment do not differ. Therefore, there is no need to worry about how to adjust cabinet doors of different types. To carry out repair work, you should open the front panels and use the adjusting bolts located on the fastening of the door with the frame.
Door adjustment
Most people who encounter violations of the correct closing and opening of furniture doors begin to get nervous and panic. As a result of this, the question arises: "How to adjust the doors of a wardrobe without harming it?". The answer is actually simple: the reason for the defect should be identified. Only after that should any decisions be made regarding repair. At the end of the regulatory process, the appearance of the doors will become much better, they will look symmetrical.
Sliding wardrobe requires a slightly different setting, unlike the usual type of furniture. In place of the usual fixtures, a retractable mechanism is placed. Thanks to this, the door leaf extends in the right direction. Furniture of this type must be adjusted using a special key with six faces.
Adjustment of doors vertically
To determine the cause of the discrepancy of the furniture doors, you should open them and look at the hinges, which act as a mechanism. By screwing and unscrewing the special bolts on the hinges, the required height of the sliding panels can be adjusted. To make it easier to determine how to adjust the cabinet door to height, the screws on the side hinges must be loosened. This makes it possible to set the door facades to the desired level vertically.
Having decided on the level of height, the screws should be screwed in at low speeds, this is necessary so that the mount holds firmly. In the case of reinforced screwing, the loops will not hold. It is imperative to know: for fasteners, only fine-threaded screws should be selected.
Adjustment Secrets
Before you break into the practical work of regulating doors, you need to familiarize yourself with the basic rules. After all, everyone should know how to properly adjust cabinet doors or any other type of furniture. General information to listen to:
- The first thing to do is align the doors with vertical gaps along the entire length of the facade. After which the height adjustment is carried out.
- Before setting up the cabinet doors, it is necessary to check whether the structure is standing or hanging. This action is performed using a small level.
- If the level on all sides does not come out, then you should pay attention to the size of the gaps. The optimal value should be no more than 5 millimeters.
- You must ensure that the door panels are seated correctly. If there are deviations, then you can fix them with a screwdriver.
In the case of the correct execution of the work sequence, the time interval allotted for regulation will be significantly less.
Configure cabinet facades
Nowadays, for more convenient adjustment, door panels are equipped with modern mechanisms. Using them, you can easily adjust the cabinet door from spontaneous opening or distortions. Visually, the adjusting bolt is placed slightly at a distance from the mounting screws. The second screw, for additional adjustment, is located closer to the fasteners.
In order to complete the full range of cabinet door setup, a figured screwdriver and a small amount of patience are needed. The hinges are fixed to the guide with a bolt, and it, in turn, rests on the cabinet frame itself.
On sliding wardrobes, the fastening system and the mechanism that allows facades to open are significantly different.
Warnings
At the time of the adjustment of the cabinet facades, there are several points to keep in mind:
- A thorough inspection is required.
- At the time of adjustment, it is necessary to hold the cabinet door so that the mechanism does not move in the opposite direction.
- Do not overtighten the screws that are located on the mount.
If these steps are difficult for one to perform, then it is better to ask for help, as an extra pair of hands will not be superfluous.