Do-it-yourself firewood can be made with ease, but before that you need to decide how much fuel you intend to put into it. Only using quality-dried fuel can you get good steam in the bath and the heat that the design radiates to heat the room. In addition, only with dry wood can you cook kebab according to the rules. If you do not want to fill the shed with firewood anymore, since there is already not enough free space in it, you can make a firewood yourself. It is important to find a place for her so that there is an opportunity to guarantee fire safety. Thus, the firewood should not be located so close to the residential building.
Size selection
Self-made firewood can have different sizes. The one that has large dimensions can be located on the street, and the one that is to be used every day can be located in close proximity to the stove or fireplace. This eliminates the need to go out of wood every time you need to flood the hearth. The described special place for storing a small portion of logs should also comply with fire safety rules, which indicates the need to give the structure the ability to ventilate. But as for the external firewood, it must be made so that it has a canopy, because water should not get on the fuel.
Varieties of firewood
If a woodcutter is made with his own hands, then it is necessary to adhere to certain recommendations on design parameters. Thus, if you want to get a firewood for temporary storage of fuel, then its capacity should be in the range from 0.5 to 1.5 m 2 , this is enough for a bath. Whereas if it is supposed to make firewood for the preparation of barbecue and other dishes, this figure may be slightly less, it can be limited to the size of 0.2-0.4 m 2 . A self-made firewood can be portable, so that it can be conveniently conveyed to the grill. Its capacity may be 0.3 m 2 .
Features of firewood
If you need to use a place to store fuel when lighting a fireplace or stove, then you can use wood or metal as the material for the manufacture. Such firewoods from willow twigs are less often performed , however they look very original and harmonious. The main feature of the portable fuel storage facility is the low weight of the product, in addition, the design should have an impressive capacity, but do not be diligent with the latter quality, because you can get a plant that will take up too much space and use it as a portable tank uncomfortable.
Do-it-yourself firewood at the dacha should be made in such a way that the bottom is solid, this will eliminate the loss of garbage and all kinds of wood residues. If a portable firewood is made, then it must be done with handles. By making a place for storing firewood, which is supposed to be used only in the house, wheels can be attached to the bottom.
Preparation of necessary materials
Do-it-yourself firewood for the fireplace can be made on your own if you can prepare some materials and tools, among them you should definitely highlight:
- Wooden blocks that will form the basis of the frame of the product. The cross section of these elements should be equal to 50 x 50 mm.
- Tes for the manufacture of a roof lathing system.
- Boards for floor mounting.
- Canvases of slate, which can be replaced with other covering material.
- Nails designed to work on a slate.
The amount of building material will depend on the size of the structure. If the woodcutter is installed on the street, then its side walls will have to be protected, for this you should use a professional sheet. However, the side walls can also be sheathed.
Firewood manufacturing technology
Do-it-yourself firewood in the country should be installed using a special technology, the features of which will be described below. As soon as you manage to choose a place for installation, you need to prepare four holes, in each of which a pole will be mounted. Depending on how spacious the woodcutter will be, the distance between the supports should be determined. Conventionally, it can be considered that the length of the place for storing fuel should be about 3 meters, while the width should not exceed 1.5 meters. In the role of supports, it is necessary to use a paired beam, the cross section of which is 50 x 50 mm. Deepen the pits by 40 or 50 cm.
The front and rear supports must have different lengths. This indicates that the pieces of timber, which will be located behind and in front, should have a length of 2 and 2.3 m, respectively. At the next stage, they must be installed in the finished pits, and then covered with stones with clay. Each of the materials is poured separately so that it is possible to perform tampering. It is necessary to protect the filled part of the supports with a special material, which can be used as an adhesive tape or roofing material. This will guarantee a higher degree of moisture insulation of the structure.
Harness installation
The binding of the mounted poles must be performed using a beam, this must be done at three levels. The bars, which should be located in the lower part, should be strengthened in increments of 10-15 cm from the construction site. As for the next beam, its fixation should be made to the central part of the supports located at the rear. After that, you can proceed to the manufacture of the upper screed, which is mounted on the rear and front posts at their upper ends.
Side supports should be fixed to each other by means of a bar at three levels. A stronger and more stable design will become if braces are strengthened to its rear and side bars.
Roof arrangement
Before you make a firewood with your own hands, you need to think about whether it will have a skeleton frame. In favor of this, it can be said that such a design will protect firewood from precipitation. Due to the fact that the poles have different lengths, the master will have the opportunity to equip a pitched roof. You can take other sizes of the posts, but the example uses a difference of 30 cm. If you provide an angle of inclination, this will guarantee the drainage of moisture.
When a firewood is made with its own hands, projects must be prepared in advance. They can be seen in the article. At the next stage of the work, you can begin to lay the crate, which is mounted on the upper screed. If there is a desire, then insulating material can be laid on the roof . As a covering material, you can use slate.
Manufacturing recommendations
When making a street firewood with your own hands, logs should be laid on the ground under the boards, the step between which should be equal to 1 m. This will allow for additional ventilation of the firewood. If the structure is installed on a solid surface, then this method should be abandoned. The wall covering should not be deaf, but leave grooves for better airflow. Do- it- yourself firewood for the fireplace is done this way . Projects of this design can be seen in the article, it can easily be done independently.