Stationary type circular saws are quite expensive on the market. However, if you wish, you can make a model with your own hands. This will require a standard set of tools. A welding machine is used to install the frame. To fix the saw blade, you need a drill. Before assembling the device, please note that the design of the circular saws can vary greatly.
Hand saw model
A circular saw (stationary) with your own hands from a hand saw is done quite simply. First of all, you need to assemble a table. For this, metal profiles are used. The ends of the workpieces are connected using a welding inverter. The saw blade itself is mounted on the holder. A simple stationary circular saw from a manual do-it-yourself is assembled with a small width pulley.
In some cases, a cover is used to protect the device. The support for the circular saw is often used rack and pinion type. Modifications with cam pins are very rare. Collector motors are installed with a power of 3.3 kW or more. In this case, it is more advisable to make the platform from a steel sheet.
Devices from the washing machine
A circular saw (stationary) is assembled with your own hands from the washing machine is quite simple. For this purpose, a motor is taken. It is recommended to select a saw blade with a diameter of up to 30 cm. The pin is used with a crankshaft. Many experts advise installing rails up to 33 cm long. The working plate is placed on the front of the frame. The feed mechanism in this case can be omitted. In order to fix the frame, a metal corner is used. The flange is most often installed behind the caliper. At the end of the work, it is important to fix the flywheel.
Modifications with one emphasis
Very often, specialists are going to do a circular saw with their own hands. Drawings on designs with one emphasis can be found in a wide variety. Many of them involve the use of cam lunettes. Experts primarily recommend starting assembly from the frame. Legs in this case can be made of wooden blocks.
After installing the working plate, guides are placed. A horizontal shaft must be secured above them. A corner is attached to the edge of the platform, and the casing is rarely used in the construction. There are also many models with a drive backrest. They differ in large dimensions. The bearing row is usually mounted above the plate. In some cases, the support is welded near the pin.
Multi-Stop Models
With several stops, it is quite difficult to assemble a circular saw with your own hands. Modification drawings indicate the need for a guide pin. The assembly of the model begins with the frame blank. For this, profiles are selected from stainless steel. It is also important to note that the racks can be fixed using a welding inverter.
Working plates are installed last. Sometimes a circular saw (stationary) is made with a do-it-yourself 3 kW collector motor. A flywheel is used to adjust the position of the lunette. The bed in this case should be fixed on racks. To change the position of the platform, a support is used.
Drawings of the device with cranked ratchet
A stationary saw is made with a cranked ratchet with a do-it-yourself stationary saw (photo is shown below) using a rack support. In some cases, a feed mechanism is used. First of all, when assembling, it is important to do the installation of the lower frame. For this, two stainless steel profiles are selected. To install the bearing row, a welding inverter is required.
It is also used to connect desktop guides. The pin is only installed with a cross member. A metal corner is soldered to the edge of the table . At this stage of the assembly, it is important to calculate the distance to the saw blade. On average, it is 22 cm. In order to protect hands, a wooden fence is used. It is important to fix the guides behind the bar. The lunette is most often installed behind the flange. For the flywheel to rotate freely, not a large lining is required. It is fixed behind the guides.
It is also important to note that modifications without a support are very common. The pins are used with gearboxes. In order to protect the hands, a small shield is installed. The bed is most often used with sharpened ends. The lunette in the design is fixed on the platform. If we consider simple models, then the guides can be used from wood. The collector motor is used for both 3 and 5 kW. Work on assembling the saw by installing the stops is nearing completion.
Sizes of saws with two lunettes
With two lunettes, a circular saw (stationary) is very easy to assemble with your own hands. The dimensions of the table in this case depend on the diameter of the saw blade. The width of the platform, as a rule, does not exceed 35 cm. In order to assemble the modification, the bed is put in the first place. Metal profiles are selected at 3.4 cm. The pins are mainly installed behind the lunettes.
In some cases, the beds are placed on two emphasis. Pinol is used with a worm gear. If we consider large-sized modifications, then they use wide racks. It is also important to note that it is advisable to install the lower block at 56 cm. In order to adjust the lunette, a rotary flywheel is used. Directly the saw blade is placed behind the caliper.
Modifications to the TS 820 Series
You can make a saw of the specified series yourself. For this purpose, the frame is installed with a width of 34 cm. The angle for the stop is easiest to make from a metal profile. The bearing row is attached to the rack with screws. Many experts advise installing lunette last. Guides for a saw are selected by 34 cm.
The handicraft is easiest to make from a wide bar. The collector motor is mounted on a saw with a power of 3 kW. The gearbox is attached to a rack on the platform. The saw blade is locked to the drive shaft. The support for normal operation of the modification should be firmly fixed. In order to protect hands, barriers can be used.
How to make a model like TS 825?
With the availability of tools, this stationary circular saw with one's own hands is easily made. Drawings for this design can be found in a wide variety. However, the most common are schemes for two lunettes. The bearing row in this case is installed behind the cross member. The collector motor is selected not high power. The pin should be installed in the central part of the work platform.
The feed mechanism in this case is not required. In order to fix the plate, a metal corner is used. Guides for a saw are used small height. For the free movement of the lunette, a flywheel with a rotary mechanism is used. The bottom block must be well protected. It is also important to pay special attention to the installation of the bed. Legs for the construction can be made from ordinary bars. Directly saw blade is placed near the central rack.
Assembling the GKS 190 Series
This circular saw (stationary) do-it-yourself can only be assembled using a 4 kW collector motor. The bearing row can be mounted behind the stand. A small flywheel is used for this purpose. It is also important to note that the pin is allowed to be used at 5.6 cm. The gearbox is most often installed behind the backrest. All this is necessary for the free rotation of the shaft. The bed in this case is easiest to make of bars. Racks are more appropriate to select a small width.
The flange is usually mounted on the edge of the platform. In this case, the drive shaft should not be in contact with the guides. The guarding tape is most often mounted behind the front pillar. The width of the platform should not exceed 68 cm. The shield is easiest to install on the screws. However, it must be at a safe distance from the gearbox. Particular attention should be paid to the lower supports. To increase stabilization, it is recommended to use only wide profiles. The height of the support in this case should not exceed 30 cm.
Modifications to the GKS 156 Series
This circular saw (stationary) is hard to assemble with your own hands. First of all, it is important to note that the motor will need 4 kW. In this case, many experts advise using only steel rails. Install them after the front pillar. The handicraft is most often made from a bar. It is also important to note that the design will require a wide emphasis.
It is advisable to install the shield near the rear support. The bearing row is mounted together with a rack. At this stage, it is important to calculate the exact distance to the saw blade. The minimum clearance is 3 cm. The bed is most often used on four legs. In order to install the guides, a welding inverter is used. The lower block is mounted under the gearbox. It is important to fix the lunette securely, and ratchet in this case is not required.
How to make a model like GKS 144?
The indicated circular saw (stationary) is assembled on a motor with a power of 2.2 kW, and the bed is selected at 40 cm. The bearing row is fixed in front of the rack. Guides are easiest to use with a small width. It is also important to note that one flywheel is required to assemble the device. He is obliged to fasten in the rotary mechanism. It is more expedient to make a shield of steel sheet. The casing in this case is not required. The legs can be mounted directly around the corner. The lunette for a saw is selected not wide. The carrier plate is fixed last.
Assembling the K-CS 1300 Series
The indicated circular saw (stationary) with your own hands is assembled quite simply. The bed for the model is used at 34 cm. In this case, the bearing row is installed behind the rack. Directly the saw blade is placed after fixing the guides. Particular attention should be paid to the collector motor. In this case, its power must be at least 4 kW.
The flange is used with a steel plate. It is more advisable to install the handrail behind the front desk. To this end, two holes are made on the working platform. It is important to fix the lunette near the motor. Saw blade guards are not required. The lower block should immediately be selectively high. The caliper should be used with a roller mechanism.
Modifications to the K-CS 1325 Series
Devices of this series are assembled using 3 kW collector motors. If you believe the experts, then the handcuffs are best used in wood. It is also important to note that the support should be installed on top of the workpiece. Ratchet in this case is not installed on the saw. The gearbox is used with one bracket.