Compressor units can only work from receivers. These devices are responsible for the pressure inside the system. Many modifications are made with relays, which differ in downforce. It should also be noted that the receivers can be equipped with sensors. Filters are most often used with clamps. If necessary, the receiver for the compressor can be made independently. However, it is important to consider the type and capacity of the compressor unit.
40 liter devices
Making a 40-liter compressor receiver yourself is pretty easy. First of all, the camera is prepared for the device. As a rule, a stainless steel sheet is used. Experts say that the lid should be welded last. It should also be noted that there are two-chamber modifications. The easiest way to use relays is low conductivity. Homemade modifications, as a rule, are not equipped with sensors. Gearboxes for devices are selected chain type. At the same time, valves with a tee are used to purge the air.
Modifications to 60 liters
An optional receiver for a 60 liter compressor can be made with two cameras. Experts say that the sheet of metal should be a thickness of 1.3 mm or more. Tees are most often installed next to a relay. Receivers of this type should be equipped with two filters. In this case, the gearbox should be installed with an adapter. 60 liter versions are great for low power compressors. The ultimate pressure indicator for systems is 6 bar. It is also important to note that during assembly only the channel valve should be used.
80 liter device
Air receivers for an 80 liter compressor are allowed to be manufactured with two relays. Experts say that filters are selected with a large diameter. The receiver outlet pipe should be at the top. Intermediate filters are mounted through an adapter. It should also be noted that modifications with stops that are inside the camera are considered common. The pressure setting for this type of receiver is approximately 10 bar. Relays they use a wired type. The maximum compression force is 3 N. Tees for modifications are selected with a diameter of 2.2 cm. It should also be noted that sensors are often installed in devices to control the pressure level.
Single Valve Models
How to make a receiver for a compressor with a single valve? Cases in this case are used on 30 liters. You can also consider more compact modifications. To assemble the receiver, the camera is first prepared. The hole for the gearbox is welded in a small diameter. Experts recommend using only wired relays with a tee. The diameter of the outlet pipe for a 30 liter modification must not exceed 2 cm. The reverse-acting valve is mounted at the base of the filter. It should also be noted that modifications to two outputs are considered common. They are great for 10 kW compressors. The pressure in the system can be maintained at 5 bar.
Two valve device
The receiver for the compressor on two valves is assembled with a capacity of 40 liters or more. On average, the pressure for models of this type is at the level of 4 bar. Devices primarily differ in relay conductivity. They have a maximum clamping force of 7 N. Many modifications are made with a contact reducer for two outputs. If you assemble a simple modification, then the tee is more appropriate to use without a sensor. It is also important to note that the non-return valve should always be installed behind the filter. Experts say that the outlet pipe is welded last.
Single chamber devices
Single chamber modification is suitable for compressor units of different capacities. Devices of this type are actively used in large factories. Modern models are distinguished by a high pressure parameter. They use a safety valve and a protected gearbox. To independently assemble a single-chamber type receiver, it is recommended to make a container for it. The relay is used with conductivity from 1.2 microns. In this case, the clamping force must be a maximum of 12 N.
Reverse valves are mounted behind the filter. The gearbox should be located at the rear of the tank. The optimal diameter of the outlet pipe is 2.2 cm. However, it is important to consider the volume of the chamber. If you assemble the device for 40 liters, then the intermediate filter is installed behind the relay. It should also be noted that before using the equipment, the camera must be checked for sealing.
Two-chamber modifications
A two-chamber home-made receiver for the compressor is made with a tank of 60 liters. Some devices are made with a sensor. For self-assembly of the model, you will need to make a camera, as well as make a hole for the pipe. The relay is standardly wired. Adapters are better to use with wraps. Experts say that the receiver must withstand high pressure. The optimal diameter of the outlet pipe is 2.2 cm. The valves for the devices are selected from steel or an aluminum alloy.
Using gearboxes with locks
It is problematic to assemble a receiver for a compressor with locks. First of all, it is important to note that models must have a high parameter of permissible pressure. Filters for devices are suitable only on liners. It should also be noted that the relay must be installed in front of the gearbox. Experts say that receivers of this type are made with small tees. Some modifications are collected with carrying. Sensors are used to normalize the pressure inside the chamber. Reverse valves are installed with partitions. They are capable of passing air in only one direction.
Devices with pressure sensors
The receiver for the compressor is made with cylinders of different capacities. Some devices are suitable for powerful compressor installations. However, in this case, much depends on the diameter of the nozzle. If we consider models for one output, then they have an indicator of allowable pressure on average equal to 5 bar. In this case, the clamping force can reach a maximum of 12 N.
Reverse action valves are installed with or without liners. Gearboxes can be found with different conductivity. Tees on receivers are installed with a diameter of 2.4 cm. If we consider simple modifications, then they use only one filter. The permissible pressure indicator for receivers of this type is about 2 bar. They are suitable for compressors with a total capacity of 8 kW.