A person who does not understand the operating principles of the washing machine sufficiently may not pay attention to the functionality of the bearing, since it is not noticeable to the eye. It is on the condition of this detail that the operation of hidden structures depends.
The opinion of experts
The average bearing life is 6-8 years. Many experts say that it needs to be changed every 5 years or at least lubricated. It will be better if the repair of washing machines, the replacement of bearings will be carried out by professional craftsmen who work quickly and efficiently.
Due to improper use of the equipment, destruction of the stuffing box and rusting as a result of water leakage, the part breaks down faster. In the vast majority of cases, a bearing malfunction is caused by increased friction and heating of its components.
Why it is necessary to change the bearing
This part of the washing machine is the most vulnerable. After all, it is with its help that the unit operates. It is possible to understand that the bearing is faulty by specific sounds, which become stronger with time.
If repair with a broken bearing has not been carried out for a long time, then the part may fall apart. In this case, its inner ring will remain on the shaft, and the outer one will fall into the tank. How to remove the bearing from the drum of the washing machine in this case? It is only possible to knock out residues from the tank using a special sharp tool.
A part not replaced in time violates the integrity of the drum. If the ring on which the oil seal was sliding broke, then there is a high probability that the shaft has become unusable, and replacing the bearing will not lead to positive results. In this case, a cross with a shaft or a drum is subject to replacement.
When the first signs of damage appear, you should immediately contact the master, since a malfunction can lead to an repair, which will cost you much more. If a bearing malfunction results in water leakage, this may cause burnout of the heating element and the electronics system. In this case, the machine cannot be restored.
Bearing replacement cost
How much will it cost to replace the bearing? If the master will carry out the work, then you will spend from 1000 to 2000 rubles. In the event of a breakdown in a vertical design car, you will have to pay 1,500 rubles. Replacing a part in a crosspiece costs 1000-1500 p. Installing a new bearing in a forecastle costs 2000 rubles.
Bearing cost
If you repair at home, the replacement will be much cheaper. You will have to purchase only new bearings, the price of which varies depending on the region of the Russian Federation.
You should inquire about the prices in the service centers of your city or in online stores. It should be noted that bearings, the price of which may vary significantly, are presented in a fairly wide assortment. They are designed for washing machines from a variety of manufacturers. For example, the drum bearing of an LG washing machine costs from 500 rubles and above. It all depends on the model of the unit.
What tools and materials will be needed
Many are interested in how to remove the bearing from the drum of the washing machine with your own hands, and what tools will be needed for this. You will find everything you need at home. The work is based on disassembling the machine. Much here depends on the company unit.
The work needs:
- ordinary and curly screwdrivers;
- pliers;
- round pliers;
- two keys on 17 and 19;
- end heads on 7, 8, 10, 13;
- rubber mallet;
- hex key 6;
- universal screwdriver;
- tight glue;
- chisel;
- rubber mallet.
First, remove the tank
The tank is first dismantled. In machines of different manufacturers, this process is carried out in different ways. After removing it, the main nut is loosened and the pulley is removed. Screws are removed with a screwdriver, fastening two parts of the tank to each other. After that, they should be unclenched carefully.
The tank is removed from the unit body and thoroughly cleaned of scale and dirty plaque. This will ensure the washing machine performs well after repair. In particular, the ring on which the oil seal slides is carefully cleaned.
How to remove the bearing
How to remove the bearing from the drum of the washing machine? After the tank with the drum is pulled out, you should proceed to disassemble it and remove the parts. If there is grease on the drum cover, this serves as an additional confirmation that the bearing and oil seals need to be replaced.
As mentioned above, the tank consists of two parts. They are joined by bolts or glue. The glue-based compound is carefully sawn. It is much easier to loosen the bolts.
After disassembling the tank, the following manipulations are performed:
- The drum pulley is unscrewed with an asterisk, a chisel or a hammer. It is not easy to remove the bolt, so it is carefully unscrewed so as not to disrupt the thread.
- By loosening, the pulley is removed from the drum screw. Underneath is the bearing.
- The drum shaft is knocked out inward. Thus, the tank and drum of the machine are disconnected. You can initially replace the new shaft with the old one so as not to spoil it with hammer blows. The bearings are located on the inside and outside of the drum.
How to knock a bearing out of a drum of a washing machine? A metal rod is inserted under the bearing race. The part is knocked out with a hammer in a circle. You can resort to using a special puller. With this tool, the bearing is removed easier and faster. You will not damage his clip. It is indispensable when the part is whole and the shaft is deformed. Usually, a small outer bearing is removed first, and then a large inner one. To remove the last tank is turned over. Before changing bearings, seals are changed.
After the parts are removed, install new ones. Work is carried out in reverse order. Before installation, bearings are lubricated to protect against water. In addition, lubrication will reduce friction between components. First of all, the internal bearing is placed. Elements are recessed by hand, and then carefully knocked out with a rubber hammer or a mallet. Put a new gasket on the halves of the tank. Sealant should be applied over its entire surface. A pulley is put on the tank and secured with a key. Screws are screwed on the parts.
Washing machines with stainless steel tanks are much easier to repair. In these models, the bearings are located in the crosspiece or the back of the tank, which is very easy to remove.
Gross errors in disassembling the machine and replacing the bearing
Specialists have identified a number of the most common mistakes made by beginners who do not know how to remove the bearing from the drum of the washing machine right. This can cause major repair problems and permanently disable the unit.
We proceed to listing:
- the wires of the hatch lock sensor come off when removing the front of the unit;
- when trying to remove the pulley from the axis, damage is caused to it;
- the thread of the attached bolts breaks;
- the filler pipe comes off with the hose;
- when the bearings are knocked out of the drum, they are seriously damaged, such a change of bearing may result in a change of drum.
Pay attention to all of the above and try to avoid the wrong actions. Replacement of the bearings of the drum of the washing machine can be carried out on their own. But remember, not having the proper experience in this type of work, you risk violating the mechanism of the unit even more. If you are not confident in your abilities, then it is advised to seek help from a specialist.
Repair of washing machines at home
Can spare parts be replaced on site? Repair of washing machines at home by a specialist takes much less time. After the cause of the malfunction is determined, the master will begin to “resuscitate” the unit, and will not postpone work until later, as is often done in the workshop for repairing household appliances.
In most cases, only one arrival of a highly qualified specialist is enough. The master has with him all the necessary spare parts. You can be sure of their originality. After completion of the repair work, the specialist will surely turn on the machine and check it in working condition. So the correctness of its repair and installation will be checked. A highly qualified master will be able to deal with even the most difficult damage in a few hours. He will clearly demonstrate the operating rules of the unit and explain to you what wrong actions on your part led to a malfunction of the equipment. The wizard will give you proper advice.
Repair of washing machines at home - convenience and benefit. In any case, the arrival of a specialist and the determination of the problem are free of charge. Repair work itself has a fixed price. Details also have a certain cost. The arrival of the master provides an opportunity to save valuable time, money and nerves. In order to avoid certain problems after the repair, resort to calling only a trusted master who will write you a warranty card for the repair work he has done and provide high-quality spare parts.
Conclusion
For example, you can purchase spare parts for Indesit washing machines at a service center that specializes in units of this brand. Specialists will be able to pick up any electrical parts, circuits, functional elements, external attributes of the case for each specific model. You will be given a guarantee for spare parts for Indesit washing machines. Professionally selected parts will help extend the life of the machine.