Perhaps, not every man visits a hairdresser, preferring to carry out all the procedures at home independently. Well, or with the help of a wife, for example. In turn, the girls are wondering about how to trim a man with a machine so that he likes it, and had to taste. There are some simple tips to help with this problem.
How to trim a man with a machine. General rules
First of all, figure out which tool you have to use. See what modes are available on the typewriter, which nozzles. Be sure to ensure that the tool head is well lubricated with special oil. Otherwise, the machine will tear the hair, and not cut. Which obviously will not please your client.
Remember: the initial length of the hair plays a huge role. As well as the desired result. In advance, discuss the final length of the haircut and bangs (or its complete absence), and whether the transitions are implied in the hairstyle, or whether it will be “under one head”. All these key points will significantly save time in the process, as well as nerves following the results of a haircut. So, before you trim the machine with a man, discuss all your questions.
If he has long hair
Not a single hairdresser's electric tool can cut a very long length. Therefore, if your man came up with the idea to radically change his hairstyle, prepare scissors to begin with. They must be sharp. Buying a professional tool for this, by the way, is not necessary at all, because in the end the hair will be cut with a hair clipper. However, the sharpness of the scissors should not be in doubt so as not to tear and not pull the hairs.
Sprinkle hair lightly with water, comb it with a comb with medium cloves. Use scissors to remove the length so that it can be "captured" by the largest nozzle of the machine. Do not touch the bangs, it is better to cut it at the last moment. If you are wondering about how to trim a man with a typewriter at home, you can peek the technology in the salon or look at the training materials for beginner male masters. This is in extreme cases, if you are not at all sure of your own abilities. But, most likely, this will not be needed, since there is nothing complicated in this process.
After the length is removed, you can start cutting with the help of nozzles. Pay attention to where and which will be used. It is better to start from the back of the head and move to the top of the head, as this is the easiest area to fill your hand. You need to cut it from the bottom up. Do not ignore the top of the head. Cut it against the direction of hair growth so as not to miss anything.
Haircut temples
When the excess hair is removed from the back, proceed to the sides. Whiskey is usually sheared with a smaller nozzle, carefully passing the area behind the ears. Carefully ensure that there is no excess hair left. Let it be necessary to once again hold the machine, but the haircut comes out smooth. To ensure that the transitions between the nozzles were not so noticeable, hold the tool at a slight angle and not close to the head. After the temples, you can immediately cut off the excess hair on the back of the neck, if this was originally intended. Be sure to brush off the hairs with a brush when changing nozzles. Firstly, it will extend the life of the tool. Secondly, the haircut will be more even and smooth.
Bang. How to cut it?
There are three options: do not touch at all, use scissors, use the same machine. If the first two are more or less simple, then the last one needs to be dealt with. When wondering how to cut a man a bang with a machine, remember the golden rule: it is better to use a large nozzle first than to cut everything to zero. Hold the instrument at an angle of 45 degrees for your convenience. If initially the bangs are too large, then remove the length with scissors, and then grasp the typewriter. Move it gently and carefully, slightly thinning out the bangs.
Haircut
Are you done Look carefully at the result. Are there any missing hairs or sticking out? If not, then remove the nozzle and without it, make a border, aligning the haircut. How to trim a man with a machine if skills are scarce? Follow this simple instruction. You will succeed. If this is your first haircut, then take an interest in how the man was cut in the salon before, where to start, how to end. Be careful. A tool without a nozzle is sharp and can cut. For example, an ear. Or the skin behind the ears.
To know how to trim a man with a machine correctly, it is enough to try once. The most important thing is to choose a good tool. So, for example, thick hair cannot be cut with a machine with little power. But such devices are indispensable for cutting children whose hairs are still thin and light. It is better to leave too powerful devices for professionals in their field. Even the most budgetary clipper can do its job well at home. And it justifies the cost of itself in just a few months with regular use.