In a modern office, old-fashioned stamps and pads replaced ergonomic automatic prints. Sometimes they are called tradates - by the name of a well-known company that produces snap-ins for them. With regular use of automatic trad, the ink on the pad dries and the prints on the paper become faint and fuzzy. Documents with faint prints do not lend themselves well to photocopies and scans. The legal departments of many companies may invalidate such securities.
If the office has a need to refill the ink pad, then it is not necessary to call specialized companies to find out how to refill the ink with printing. Refueling instructions are usually available in special boxes that sell automatic accessories. A standard recommendation is to buy a new stamp pad for printing. But this advice can cost the company quite expensive. Therefore, we will try to find out how to refill the print with ink without damaging it, and at the same time not get dirty.
How to pull out the stamp pad
In standard automatic printing, the stamp pad is in the middle. It can be seen when viewed from the side. A photo of automatic printing indicating the position of the stamp pad is located below.
To understand how to fill a round seal with ink, you need to remove this pad. To do this, press the two buttons located on the sides of the tradat, while slightly pressing the print down. If everything is done correctly and the automatic equipment has not been damaged, the buttons will fix a slightly pressed state. After that, using an ordinary pencil, gently pull out the pillow from the side gap.
How to prepare a print for refueling
Before refilling the ink, clean the removed pad and remove adhering lumps of paint, pieces of paper, and other possible contaminants. Various dents left on a soft surface, it makes sense to smooth out a non-sharp object. An ordinary paper clip is perfect for this. With the end of it, carefully align all the prints. A worn pad is not elastic, it practically does not absorb ink, and deep dents that cannot be smoothed out are visible on it. It does not make sense to impregnate such a pad with stamp ink, it is better to order a new one - and then you will not need to learn how to refill the ink with printing. The photo of the pulled out pillow can be seen below.
How to apply stamp ink
Thus, the printing pad is prepared for stamping with ink. The required paint is produced by various companies, including in our country. In no case should you refill the print with mascara or other liquids - you can quickly and hopelessly spoil it. The standard ink bottle has a dispenser, which is very convenient to drip on the print.
A few drops of the ink should be gently and evenly applied to the surface of the pad. Excess can be removed with a napkin. After painting, you should wait a few minutes until the liquid is absorbed into the surface. Insert the pad into the print equipment with the ink side down. To answer the question of how to properly refill printing with ink, if two or three colors are used in automatic printing, you just need to sequentially pull out pads of different colors and fill them with the corresponding ink stamp. The sequence of operations is the same as with monochrome prints.
Flash print
Recently, prints of a new type - flash prints - have been widespread. They differ from the usual stamp in that their working surface, which is applied to the print, is absolutely smooth. This print uses several colors, it is more accurately and evenly applied to the paper. Flash prints are much more durable, and their level of protection is an order of magnitude higher.
One-color Flash Printing
Despite the durability and wear resistance, after some time, the question still arises as to how to refill printing with ink. In order to quickly fill up flash printing in a simple way, you need to have a syringe and a suitable ink on hand. The cliche is located on a cushioning printing pad. Remove the cliche and put it on a flat surface. Apply the paint evenly several times with a syringe. Between applications, wait a while to ensure that the ink is evenly absorbed in the cliche. The layer of the applied liquid should not exceed 2 mm. Let the ink soak completely, wipe off any excess ink with a tissue and collect the print in its original condition.
Refill multicolor flash printing
When refueling multi-color flash printing, you need to get the cliche as described above. This part is filled with syringes, while carefully monitor that the paints do not mix. Paints of different colors have varying degrees of fluidity. Remembering how to refill ink is easy: first, paint is applied to one print segment, then to another. When refueling, a separate syringe must be used for each color, otherwise the colors will be dirty and blurry. After the ink filling procedure, the cliches of the flash print should be set aside. The paint should be evenly distributed over the surface, this takes some time. After that, insert the cliche into place and try the prints.