A standard engraving machine allows you to make real masterpieces from stone, wood, metal and glass. This is a highly specialized tool that makes it possible to make thin cuts in any hard-to-reach places. In addition, the machine is equipped with various abrasive wheels as standard. We study the characteristics and features of this tool, as well as consumer reviews about the manufacturers of these devices.
Engraving machine Dremel / 8200 / 1-35
The spindle of the specified device spins up to 30 thousand revolutions per minute, the speed is adjusted using the slider in the rear compartment of the housing. In the same place there is a socket for a modern lithium-ion battery, which lasts for 15 minutes of continuous operation. Battery charging time is not more than an hour. A replacement analogue is not supplied, but is compatible with the identical version of the Bosch brand and some other modifications.
Advantages of the grinding and engraving machine :
- The presence of an automatic brake device that stops the motor immediately if necessary, increasing the safety of operation of the tool.
- High rate of power.
- The presence of a special handle for using the engraver in artwork.
- Rechargeable lithium-ion battery.
The disadvantages include the lack of a spare power source and sleeve.
Hitachi GP10DL
This is one of the most popular engraving machines in the domestic market. It has a speed of 3.5 thousand revolutions per minute; it is distinguished by high quality product processing. As a regulator, a primitive circuit is used with windings that correct the voltage, increasing or decreasing the torque on the spindle.
Together with the battery, the mass of the device is about 500 grams. As a battery, a lithium-ion cell is used that runs continuously on a single charge for about an hour and a half. This part thoroughly spoils the balance of the device, however, it allows the use of a flexible sleeve in the form of a nozzle, for the fastening of which a thread is provided. It is also possible to turn on the LED backlight.
Additional batteries can be bought without problems, they are inexpensive and maintain a decent level of capacity. Charges for continuous operation lasts about forty minutes. Among the advantages, users note a high rate of engine operation and a long service life without recharging. The disadvantage is the inconvenience of using without a flexible hose nozzle.
Makita BGD801Z
The engraving machine from this manufacturer is more suitable for home self-taught masters. This is evidenced by the shape of the body in the form of a dumbbell and a decent weight (1.7 kg). Tool collets make it possible to use tooling with a shank of three to eight millimeters. This design is great for processing metal joints and seams.
The specified device proved to be quite good as a good locksmith tool. Among the shortcomings, consumers point to a rather heavy lithium-ion battery that offsets the balance and loads fingers during operation. In addition, a spare battery is not supplied, a charger also. This indicates the ambiguous attitude of the manufacturer towards customers who will have to spend a fair amount on the purchase of these elements. Among the pluses - a powerful motor and a high margin of work on a single charge.
Elitech PShM 170EZhK
The manual engraving machine has a specific grip of the handle with a high ergonomics index. The mass of the device is 750 grams, power - 170 watts. Ease of use of the device is the presence of a removable handle.
Features:
- There is a digital speed sensor.
- There are plus and minus buttons for adjusting the operation of the device.
- The standard equipment includes several nozzles, including a flexible sleeve with a stand for heating the engraver.
BISON ZG-130EK H242
The wood engraving machine has a rather controversial design. It is not the most powerful among competitors (130 W), however, with a speed of 30 thousand rotations per minute and a mass of 650 grams, it surpasses the Chinese counterparts in most indicators. The device is equipped with a reliable motor that does not overheat almost until the smell of burned plastic.
The entire control panel is placed on a small pistol-type handle. Not all users liked this solution. Firstly, hold on to the body with only two fingers. Secondly, when holding the device, the deactivation key is between the hand and the handle, which is quite inconvenient. Variations with a hanging bar and a flexible shaft are much more convenient. In addition to the main tool, a standard case includes a portable suitcase with a set of various nozzles.
Engraving machine Ryobi
Below are consumer reviews of this brand of engravers. Among the advantages:
- Affordable price.
- High rate of power.
- Suitcase case with a lot of nozzles.
Disadvantages:
- There is a rapid heating of the case.
- Difficult to find some spare parts.
- Low build quality.
Skil 1415 LC
This novelty looks quite attractive, equipped with an ergonomic body with soft elastic pads. The set comes with a flexible shaft, a fixing clamp, a telescopic suspension, a tilt-adjustable handle with a built-in flashlight. Moreover, the price is relatively affordable.
In terms of quality, the engraving machine of this brand leaves much to be desired. Owners note poor Chinese assembly and the unreliability of a spindle engraver. Experts recommend checking the devices for the presence of backlash and vibration. The power unit is capable of accelerating to 35 thousand revolutions per minute, has a primitive speed controller.
The general equipment of the tool is a weak stand and shaft, which are also inherent in the "Whirlwinds" and "Caliber". The spindle heats up quickly, not designed for continuous operation.
Sturm! GM2317FL
This metal engraving machine is equipped with a non-standard mechanism in the form of unconventional illumination of the working area. It is not an LED, but a flexible flashlight on a flexible basis of a removable type. In certain cases, such a decision is advantageous.
"Storm" has a power of 170 watts, develops about 32 thousand revolutions per minute. It is worth noting that at low stages the rotational force drops noticeably, as on most models with a primitive adjustment of revolutions. The owners indicate that a flexible shaft is supplied complete with the tool in question, which significantly overheats and backlash. The optimal application of the modification is small metalwork and carpentry work that do not require long-term operation of the tool.