This article will describe how to disassemble a washing machine from different manufacturers. You will need the ability to use various tools.
Undoubtedly, many models of units have inherent technological features only to them. In some of them, certain fasteners are used. Sometimes the appearance of the parts varies, but in general the circuit of the washing machine looks standard.
Necessary tools
Many people ask how to disassemble a washing machine. To disassemble the device you will need certain tools. Most of them are read by each owner.
You will need:
- curly and slotted screwdrivers ;
- wrenches of different sizes;
- hammer;
- simple pliers;
- curved pliers;
- ticks;
- nippers;
- round pliers.
All tools must be insulated. Do not forget to disconnect the unit from water and electricity. So that further assembly of the machine does not bring difficulties, it is advised to photograph especially difficult places of fasteners and removable parts. It’s also good if you have a washing machine circuit in front of you.
How to disassemble the "Ariston"?
How to disassemble the Ariston washing machine? First of all, remove the panel located at the top. For this purpose, 2-3 screws are unscrewed (depending on the design of the device).
After that, slide the panel back and remove it. You have room for further action. Details such as the engine, solenoid valves, heating elements, counterweights and other important components become visible.
Next, two bolts that lock the hatch are unscrewed. All latches are removed, after which it is possible to remove the front panel.
Then you can remove the hose suitable for the tank. In this case, pliers are used. They remove the locking clamp. Next, the hose connected to the pressure switch is removed. For this purpose, the clamp is also removed.
It is necessary to remove the clamp located inside. It serves as a rubber cuff retainer on the unit tank. The cuff itself is also removed. Next, remove the rear panel, mounted on the screws.
Then the balances should be removed. They can be located both front and rear. Their fastening is provided by two long bolts, which should be unscrewed and the parts removed.
Next, we extract the heater for heating. In Ariston washing machines, it is located in the rear under the tank. For this purpose, the locking nut located in the middle is unscrewed. Then they press on the stud, the part with which the nut was twisted. Push it in with light strokes of the hammer. The heater is pry off with a screwdriver and removed.
Then the drive belt is dismantled. It goes from the engine of the unit to the pulley. All wires in the tank and motor are disconnected. The locking elements of the engine are removed.
The tank remains suspended on the springs. Below are the shock absorbers that need to be unscrewed and the springs slowly removed, and then remove the tank.
Dismantling the tank is a simple matter. First of all, the bolt holding the pulley is unscrewed. It is removed. The shaft is pressed into the tank. Next, the tank is divided into two halves. For this purpose, remove the clamp.
How to disassemble an LG machine?
How to disassemble the LG washing machine? First, the display board is dismantled. It is fastened on two sides by means of latches.
Next, the module is extracted. It is necessary to disconnect all the connectors and wires. The pulley is dismantled by unscrewing the bolt located in the center (the machine is equipped with the usual right-hand thread). When removing the belt, pay attention to the location of the letters on the inscription so that nothing gets confused during installation.
How to remove the loading door LG
The loading door is removed from the front. It is secured by two screws. Next, the corrugation clamp made of rubber is dismantled. The electrical water supply valves are screwed in with two bolts on the rear panel.
Remove the container for washing powder
The powder container and its matching rubber tubes are also removed.
For convenience during repair, it is necessary to remove the upper corner on the front part, since it is impossible to pull out the drum with this part. Next, you need to disconnect the mount located at the bottom (there are two of them).
Bottom drum mount
By pressing on the antennae, you can achieve an easy exit of the drum from the landing site. After dismantling, the drum is located only on the holding springs located on top. Getting to the next stage, it is advised to call for help of one more person.
Dismantling side drum weights
Holding the springs, you can remove the drum from the unit body. Next, you need to dismantle the side and top loads. The latter is better to remove before removing the drum. So you lighten the weight of the structure.
As a result, only the casing remains from the washing machine. The next stage is the dismantling of the ring for the stopper that holds the corrugation.
Dismantling the machine of the company "Electrolux"
How to disassemble the washing machine "Electrolux"? If there is a disposable tank in the assembly design after the machine is repaired, it is advised to replace it with a new one. The need for such manipulation arises if it is necessary to separate the crosses from the drum. The cross must be replaced if the bronze bush is worn out.
How to unscrew a pulley bolt ?
How to disassemble a washing machine drum? The drum should be dismantled not only if some foreign object has got into it, but also when changing bearings.
The washing machine "Electrolux" is represented by many models. At the units of this company, tanks can have an excellent configuration, but the disassembly rules for all machines are approximately the same.
The pulley is first removed. It is attached to the drum shaft by means of a special bolt or a nut in the middle. The item is unscrewed with a wrench counterclockwise. It is advised to put some object underneath, for example, a wooden beam. So you will avoid scrolling.
Removing the bolt may seem like an easy task, but it is far from the case. The pulley is mounted by means of a special compound, which is poured inside. It prevents the parts from spinning when the machine vibrates.
How to disassemble the washing machine if the bolt does not lend itself to the first time? It is advisable to use a gas burner to heat the metal. So the bolt will give in to you easier. Before using the burner, read the safety instructions, as working with this device is far from safe.
Tank disassembly
How to disassemble the washing machine after the bolt from the pulley is removed. Go to removing the pulley from the drum. To do this, try to swing the tank of the machine from side to side, while pulling it toward you. Here you will also need a block of wood. Beat until the shaft aligns with the bearing or the drum hits the front panel of the tank.
The tank is unwound slowly in a circle. In some models, instead of bolts, special brackets or latches are used. They are taken out on the same principle. After removing them, it is necessary to separate the two halves of the tank.
If the tank no longer holds anything, then it is removed from the housing.
How to care for a washing machine?
Experts give a number of tips that will help to carry out proper care of the unit. So your "assistant" will last longer.
- The external and internal surfaces of the machines should be periodically wiped. So you save the device from water stains. To clean the outer panel, you can resort to the use of liquid cleaners. The inside of the drum is wiped with a damp cloth.
- After each wash, the hatch door should be kept open for a while. So the water remaining inside can erode.
- Rinse the air conditioner container without using cleaning agents.
- If the machine began to wash worse, and an unpleasant odor appeared in it, then you will need thorough cleaning. For this purpose, a special tool is used, which can be done at home. Mix 1 tbsp. a spoonful of powder with a quarter cup of bleach for laundry. The resulting mixture is poured into the machine, and the pre-soaking program is started. Then the machine is put into rinse mode. After the process is complete, make sure that the entire solution is completely removed from the drum.
- If you use the top panel of the machine as a table, it is advised to cover it with oilcloth so that it does not get dirty and is not covered with scratches. Do not put knives and other sharp objects on it. Avoid ingestion of corrosive agents.
- Drain hoses must be changed every five years and regularly checked. They should not have cracks or signs of wear.
Observing a number of simple rules, you can keep the unit in working condition for quite a long time.