Indesit brand washing machines are of good quality. However, they have certain disadvantages. First of all, it is worth noting that many machines quickly wear out the belt. Filters need periodic cleaning. Some owners say that the motor may burn out. At the same time, belt drives fail.
If the Indesit washing machine does not turn on , you can always find out the cause of the breakdown yourself. Modern devices are made with a display, and a trouble code is displayed on it. It’s much harder to fix the problem.
Models Indesit Wisl 103
These models are manufactured with a simple belt drive. If the Indesit Wisl 103 washing machine does not turn on correctly , experts advise that you first inspect its motor. To this end, it is necessary to remove the model panel and unscrew the protective plate. The motor in this case is located at the bottom of the device. The following are the stops on which the part is located. In order to disconnect the motor, you will need to disconnect all the wires. To diagnose this element, it is better to contact a service center.
Repair Indesit Iwsc 5085
This model has a rather narrow drain hose. If the Indesit Iwsc 5085 washing machine does not turn on , and water does not fill into the tank, it is recommended to check the pipe. To do this, you need to turn the model back. In this case, it is important to immediately disconnect the device from the network and water supply system. To block the water, you must use a wrench. Next, you have to clean the pipe. To do this, you can use a regular rag.
If the integrity of the tube is broken, then it will have to be replaced. It is also worth noting that problems can often lie in the filter. The specified part is located at the bottom of this model. To clean the filter, you can use a small stick. Still need a little cotton.
Model Indesit Wite 107
This model is made with a high-quality motor. However, she installs a small transmission unit. This device works from a modulator. If the Indesit Wite 107 washing machine does not turn on, and the error A2 is displayed, then the unit is out of order. To inspect and repair this item, you must open the lid of the washing machine. Further, it is recommended to carefully inspect the motor.
If the darkening is not visible on it, then the problem is in the gear unit. In order to remove it, you will have to unscrew the model gearbox. It is located in the washing machine next to the motor, and is mounted on nuts. Thus, the part can be twisted with an ordinary small screwdriver. The next step goes directly to the gear unit. Then it must be inspected for defects. As a rule, during overload, the contacts of the model burn out. The cause of this failure is caused by a network failure. To fix this type of fault, you will have to replace the gear unit in the service center.
Crash Indesit Wise 10
This model works from a contact rotor. The motor in this case is very rarely broken. When the rotor fails, the model displays error A3. If the Indesit Wise 10 washing machine does not turn on, experts advise inspecting the unit as well as the gearbox. To do this, the model cover is removed and the integrity of the module is checked. Then you can do the gearbox. In this washing machine, it is located under the rotor cover.
The gearbox can be removed with a wrench. Next, the integrity of its plate is checked, and the upper part of the part is inspected. Sometimes a plaque appears on it. This is due to water leaks. If after cleaning the rotor refuses to start, then you can simply replace the device. To do this, just find out its marking and contact a service center. You can supply the part yourself. The main thing - during installation, do not damage the wiring of the motor.
Model Indesit Wil102X
This model is famous for its good gear unit and high-quality drum. Some customers complain that the water level sensor often fails in the device . When this happens, the display shows A5. If the Indesit Wil102X washing machine does not turn on, then the sensor must be changed. In this case, you have to completely remove the drum model. However, the lid is first disconnected. The next step is to remove the protective harness, which is located near the drum. Next, you need to twist the head from the central stem. You can do this with your hands. It is difficult to remove a drum for one person. In this case, it is better to ask for help from a friend.
Further under the module you can notice a small box, which is a sensor. The specified element is fixed on the body with two bolts. When twisting the element, it is important not to damage the wiring. After disconnecting the sensor, inspect it and check the seal. When the pad is erased, the body of the element begins to pass water. All this suggests that the sensor will have to buy a new one.
Repair Indesit Wisn 101
This model has many advantages. However, users note a weak tourniquet that is mounted on the drum. If, for this reason, the Indesit Wisn 101 washing machine does not turn on, the display will show A6. To repair the model yourself, you will have to prepare the necessary tools. First of all, it is recommended to pick up a set of screwdrivers. You also need a large key under the stem head. To start the repair, the cover of the washing machine, which is located on the rear panel, is removed. The next step is to disconnect the rotor box.
If this is not done, the stem will be difficult to twist. In order to disconnect the rotor, you will have to use the key. The next step is to unscrew the stem directly. The ram must be disconnected by hand. It is important to fix the protective harness. If the tape is cracked on it, then it needs to be replaced. To do this, you need to find out the diameter of the tow, which is indicated on the outside. After that, you can put the drum in place and install the rotor.
Motor failure
Motors rarely break down on Indesit washing machines. However, such cases do occur. For models of the latest series, error B3 is displayed. The cause of the breakdown most often lies in the heavy load of the device. At high speeds, the motor heats up. If it is washed for a long time, then it may not withstand the load. When the Indesit washing machine does not turn on, you need to inspect the part. If the adapter burns out on the motor, then it will have to be completely replaced. The cost of the part depends on the model series.
Causes of damage to the tachometer
When the Indesit washing machine does not turn on and the E3 code is displayed, it means that the sensor has stopped working on the model. The cause of this type of failure lies in the overheating of the capacitor. This happens most often due to network outages. If necessary, the tachometer can be changed independently. Before this, the washing machine must be disconnected from the network.
The next step is to unscrew the nuts on the back cover of the model. After that, the protective plate of the module, which is located at the top of the washing machine, is removed. In order to get the tachometer, you need a screwdriver. For models of the latest series, this element is fixed on two screws. After disconnecting the device, the bottom of the box is inspected. When an element overheats, it often darkens, an unpleasant smell is felt. In this situation, the sensor will have to be replaced. After that, it is necessary to reinstall the protective plate, and fix the cover of the washing machine.
Temperature Sensor Errors
Temperature sensors rarely break in models. If the inscription B1 is visible on the display and the Indesit washing machine does not turn on, then the problem is with this element. First of all, we need to understand the causes of the sensor failure. Experts say that it crashes due to dirty water. Also, the problem may be the wear of the relay. To inspect the element yourself, you will have to completely twist the module. For this purpose, the cover and the protective plate will be removed. Next, you will first need to inspect the module. Experts recommend checking the part with a tester.
When the resistance is more than 50 ohms, the problem is with this component. If the testing of the module failed, and the Indesit washing machine does not turn on, it means that the sensor must be checked directly. For many models, it is located behind the outlet pipe, and is fixed on a rack. A small contact departs from it, which connects to the board. To disconnect an item, it is important to carefully inspect the device mount. For models of the latest series, the sensor is fixed on one clip.
Causes of damage to the level sensor
Sometimes washing machines break level sensors. These elements fail due to malfunctions in the module. Also, a network congestion may cause a breakdown. Level sensors cannot be repaired, but can be changed. To this end, it is necessary to verify the breakdown of the elements. To do this, remove the lid from the washing machine, and inspect the drum. Level sensors are located under the plate, and are connected to it through the contacts. If the tester shows a zero value, then the device is broken. It needs to be changed.