Motobur Champion AG252 is a fairly lightweight and compact device, inside of which a high-performance powerful engine is installed. He usually helps to solve everyday problems in the country, in the garden and outside the city, when there is a need to go fishing in the winter. Its cost is not so high compared to peers. That is why the model is popular. To guarantee long-term use, you should familiarize yourself with the rules for using and storing the tool, which will be described below.
Field of use of a motor-drill of the Champion brand
With the help of a powerful motor, the unit performs work on drilling holes in the ground for planting plants and installing poles under the fence. This tool was developed to solve problems in areas where the use of heavy equipment is impossible. The equipment is used for public purposes. When installing a special drill perfectly copes with the preparation of holes on ice. The unit found its application when it is necessary to quickly plant plants in the garden. It is noteworthy that the Champion AG252 motor drill is supplied complete with a drill on the ground, the dimensions of which are 200x500 millimeters.
Positive characteristics
The power of the equipment, which is equal to 1.46 kilowatts, is enough to ensure stable operation even at the highest loads. The manufacturer took care of the presence of an excellently regulated ignition system, which contributes to a quick and easy start. As practice shows, the air filter can be easily removed, which prevents its pollution and significantly extends the life of the filter. The connecting rod of the product and the motor shaft are made by the manufacturer of high-strength steel, which contributes to the maximum possible strength of the device.
Motobur Champion AG252 has a diaphragm carburetor. It provides stable operation in any position. Overheating of the engine is not possible, since an air cooling system is installed inside. If your site has high density soil, then a durable gearbox and gear ratio (40: 1) will provide easy operation. The device is designed in such a way that the controls are very convenient. The whole design is ergonomic, so the master can easily adjust the operating mode even with one hand. As additional advantages, the presence of an anti-vibration system and a low noise level should be highlighted, which increases comfort during work.
Specifications
You can buy the Champion AG252 motobur for 11 600 rub. Its power is 1,460 watts, and in horsepower this figure is two. The working volume is equivalent to 51.7 cubic centimeters. The maximum diameter of the drill is 250 millimeters. Only one operator can use the machine. Before purchasing, you should be interested in such characteristics as tank volume, weight and type of cartridge. We will tell you about them in detail. For example, 0.98 liters will fit in a tank. The weight of the device is equivalent to 5.9 kilograms, and the cartridge has a length of 20 millimeters. In one minute, the working part of the tool makes 2800 revolutions.
Equipment
A motor-drill for Champion brand posts provides for an engine assembly, as well as gloves and a container for preparing the fuel mixture. You do not have to purchase a set of keys, glasses and a repair kit that comes with the kit. In packaged form, the product weighs 9.2 kilograms. And its dimensions are 590x350x400 millimeters. The brand is home to the United States. However, the manufacturing country is China.
Reviews
Champion's pillar drill has a two-stroke single-cylinder engine. According to users, this equipment is covered by the warranty for 1 year, which is given by the manufacturer. The device is included in the line of budget gardening equipment. It is widely used in construction, utilities, agricultural and other domestic works. As users emphasize, the device is equipped with a fuel tank, which is filled with a mixture of gasoline and oil in a certain proportion. Among the additional advantages, according to customers, are budget, high build quality and materials used, as well as low weight.
Recommendations for use
A motor drill for fishing should be refueled with a fuel-oil mixture. For its preparation, unleaded gasoline with an octane rating of 92 should be used. It is mixed with engine oil intended for two-stroke engines. In this case, use the ratio of the first ingredient to the second in a ratio of 50 to 1. Never pour oil that is designed for two-stroke engines with water cooling. The use of a fluid that is used for two-stroke engines with low maximum revolutions is unacceptable. Not suitable for this equipment and oil for four-stroke engines.
Motobur for fishing will work properly if you properly prepare the fuel-oil mixture and store it under certain conditions. To do this, use special metal containers or products made of non-food plastic. The mixture should be prepared in a well-ventilated area or outdoors. It is forbidden to cook it in the tank of the device. Half the prepared gasoline should be poured into the container, add the required amount of engine oil, close the lid tightly and mix the fuel mixture.
The lid of the container opens, allowing air to escape. Then add the remaining gasoline, close the container and thoroughly mix again. Before refueling the fuel tank, it is necessary to shake up the liquid mass in the tank. It must be consumed within 30 days after preparation. With prolonged storage, the composition oxidizes and becomes heterogeneous. Never refuel with clean gasoline.
Champion AG252, reviews of which you will read in the article, will not be repaired under warranty in the event of a breakdown. For example, if the engine fails during operation with an improperly prepared fuel-oil mixture. Do not store the unit with fuel in the tank in a closed room, as the mixture vapors are explosive. The engine should not be run in and left for a long time at idle. It will reach maximum power only after developing 10 full refueling of the fuel tank.
Service Features
The Champion AG252 gas drill must be disengaged every 25 hours. At the same time, the filter is removed, which is washed in gasoline and dried before reinstalling. The quality screw allows you to adjust the ratio of fuel to oil at maximum engine load. Its tuning is carried out by tachometer. The screw, which is indicated by the letter L in the instructions, will allow you to configure the engine idle. This will provide excellent idle stability. It is important to remember that high position and weather conditions can affect carburetor performance. If you purchased equipment of the brand AG252 Champion, the instructions before you start using the instrument should be read by you. From it you can find out that the fuel filter must be periodically checked. If it is very dirty, then it should be replaced.
A dirty filter can cause difficulty starting and lower engine performance. It is important to clean the cylinder fins with a brush or compressed air, since contamination of this element can lead to overheating of the engine. It is important to check the drill by sharpening it or replacing it if necessary. Spare parts for the Champion AG252 motor drill, in particular a replacement tip and an irreplaceable knife, can be purchased from the manufacturer. Periodically it is necessary to check the condition of the blades and repair them. This also applies to the tip of the drill.
Storage recommendations
Before long-term storage, it is necessary to clean the equipment and lubricate metal parts. Fuel should be drained from the tank and close the lid. The candle must be removed. The stator cord needs to be pulled a few times, which will allow the crankshaft to crank and distribute the oil. Then the candle is put in place. The engine should be wrapped in a plastic bag, and the motor drill itself should be stored in a dry place, preferably away from heat sources.
Trouble-shooting
If the engine does not start, the malfunction may consist in wetting the spark plug or the presence of a gap. In some cases, the insulation is damaged. If the candles get wet, they should be cleaned and dried, and if there is a gap, it must be set to a mark of 0.6 millimeters. If the distance between the rotor and the stator is too large, then it should be adjusted to 0.4 millimeters.
Sometimes the problem is insufficient engine power, and the cause may be air penetration into the fuel pipe connection. If it gets into the carburetor connection, tighten or replace the gasket. Stopping the motor while the equipment is in operation may indicate a damaged piston or a bad magneto. In the first case, the piston should be replaced or repaired, but in the second case, the condition of the spare part. If there is water in the fuel, it should be disposed of by filling the tank with a new mixture.
Conclusion
Motor drill Motor Champion AG252 motor drill, for which you can buy a screw at a cost of up to 1000 rubles, can work with interruptions, expressed in the absence of rotation during engine operation. This problem is indicated by a damaged clutch or failure of a fixed landing between the output shaft and crankshaft. In both cases, the corresponding parts must be replaced.