The Termeks water heater (80 liters), the instructions for use of which will be described below, are manufactured using modern technologies, and high quality materials are used in the process. Such devices have shutdown protection, which provides electrical safety during operation. This equipment can be used to provide hot water to industrial and domestic facilities that have a cold water supply. The system must maintain pressure, the level of which is from 0.05 to 0.6 MPa. The device must be used in heated enclosed spaces. The device must not be operated in continuous flow mode.
User's manual
If you decide to choose a Termex water heater (80 liters), the instructions for use of which will tell you how to extend the life of the device, you should be aware that the models are for sale with mechanical and electronic controls. In the first case, on the external panel there are keys responsible for selecting power. By activating both, you will provide power equal to 2 kilowatts. This will provide for the needs, based on the amount of hot water that needs to be obtained.
When using a heater, you can adjust the temperature using the toggle switch located on the control panel. Turning it counterclockwise until it stops, you disconnect the water heater from the network. If you turn the knob clockwise, then you can increase the temperature of the coolant to 75 degrees.
Using an electronically controlled model
The Termex water heater (80 liters), the instructions for use of which is included with the device, can be electronically controlled. In this case, turning on or off can be done with the left button, which is located on the panel. The display will show the heating temperature, and after 2.5 seconds you can already see the current temperature of the water in the heater. If necessary, change the temperature of water heating when an electronically controlled model is available, you can use one of the three touch keys.
Different operating modes
The Termeks water heater (80 liters), the instructions for use of which will allow you to carry out the installation yourself, can work in one of several modes. The first time you turn on or after a power outage, a temperature of 75 degrees is set. If we are talking about models with an electronic panel or digital sensor, then after a power outage the equipment goes into the “Demo” mode, which involves a demo mode. Heating elements will not be included.
Accumulative electric water heaters “Termex” can be removed from demo mode by simultaneously pressing and holding for 5 seconds the keys that are located on the control panel and indicate movement up and down. The device can go into standby mode, it is accompanied by a blinking company logo, and the indicator indicates the level of water temperature in the heater.
Residual current device during operation
Operation of the Termex water heater may be accompanied by a tripping device. In order to return the equipment to working condition, you must press the button of the same name. If at the same time the protection worked again, you need to contact the specialists of the service department, as soon as they can eliminate the cause of the breakdown. If you do not intend to operate the water heater in the winter, then it is likely that not only the appliance will freeze, but also the water mains. In order to eliminate this trouble, you must turn off the power and drain the water, only in this way you can avoid damage to the internal tank.
Connection to the water supply system
The Termex water heater, the connection of which is best entrusted to specialists (only in this case the equipment warranty will apply), must be installed in several stages. The safety valve is initially installed at the inlet of cold water. In this case, it is important to ensure the tightness of the connection, to use an insulating material like FUM tape. The manufacturer prohibits using this type of water heater without a safety valve or operating it in tandem with valves from other companies.
In the process of using the described water heater, the appearance of droplets that leak from the drainage beak of the valve may occur. This may be due to excessive pressure during heating. Users are advised to attach a silicone or rubber tube to the drainage beak, which will allow moisture to escape. The Termeks water heater diagram is presented in the article, it should help you if you need to connect equipment to the water supply system. The master must remember that the cold water supply pipe must be located below the hot water intake pipe. It is necessary to use metal-plastic, copper or plastic pipes in the process. A flexible plumbing eyeliner will help with these manipulations.
It is recommended to supply the heat carrier to the water heater after the sump, which should be located on the cold water main.
Additional connection recommendations
As soon as Termex accumulative electric water heaters are connected, the cold water supply valve can be opened, this also applies to the hot water tap on the mixer. So you can ensure the outflow of air from the device. When cold water flows in a continuous stream from the mixer tap, this will indicate that the filling of the water heater is already completed. If the device is installed in a place where the water supply is not connected, cold water can be supplied from the auxiliary tank. However, it must be placed at a height of 5 meters from the upper point of the device. If this is not possible, then it is additionally permissible to use a pumping station.
Note
Today, electric storage water heaters are very popular. Reviews "Termex" has a positive. These devices can be operated on a lighter basis. To do this, it is recommended to install a drain valve. This applies to those models that do not have a drain pipe in the kit. If it is necessary to install a water heater in a system where the pressure is higher than the above, a gearbox must be placed at the inlet of the equipment, which will have to be purchased separately. With it, you can reduce the water pressure to a nominal level.
Maintenance Recommendations
It is important to remember that due to the poor quality of water, scale can form on the surface of the heater, which will certainly cause damage to the elements. This case is not covered by the warranty. In order to carry out maintenance, you will need to perform a series of actions. Among them, it is necessary to highlight the connection of the water heater from the mains, the shutdown of cold water intake, as well as the removal of the safety valve.