The quality of tap water leaves much to be desired in most regions of our country. Therefore, many owners install additional filters. They allow you to achieve high quality cleaning. One of the popular filters is Aquaphor OSMO-50 (version 5). Reviews on the presented system should be considered before purchase. Features of installation and operation will be discussed later.
general characteristics
The filter "Aquaphor OSMO-50" (version 5) is a reverse osmosis system designed for deep purification of water from salts, purification of colloidal, mechanical particles, as well as organics, viruses and bacteria. Foreign odors, an unpleasant aftertaste are removed from the liquid. The system can be used to purify water from a well, municipal water supply.
During operation of the device, liquid passes through a semipermeable membrane. In this case, pressure is applied from the water side.
The presented device comes in two versions. The first of them works under the pressure that exists in the water supply network. If it is low (does not exceed 2 atm.), You need to purchase a second modification. This is "Akvafor OSMO-50" (Spanish. 5) PN. It comes complete with a pump that increases system pressure.
Both varieties have high quality cleaning. These are ultrafine filtration devices. This result is achieved due to the presence of a membrane and pre-filters. The system removes all harmful impurities from the liquid. Only water molecules can pass through the membrane. All chemical elements that are larger in size remain on the other side of this barrier. The result is crystal clear water.
Chlorine, petroleum products, nitrites and nitrates, organic matter and mechanical pollutants are removed from the fluid entering the system. In addition, the water softens, since hardness salts are removed from it. Therefore, it can be used for cooking; scale will not appear on the walls. This is especially important for some varieties of kitchen appliances, such as coffee makers.
Specifications
The package includes several required components. One of them is a storage tank. The fact is that the system cannot filter the liquid quickly. To meet the users' need for clean water, a tank is installed in the system. It has a volume of 12 l in the model "Aquaphor OSMO-50 A" (version 5). 10 l is its useful volume. It is made of metal.
The system is designed to be installed under the sink. Filters have an open housing. The system is designed to filter liquid in a cold water supply system. The temperature of the liquid should be 4-38 ° C. The working pressure in the water supply should be 2.8-6 atm.
The water purifier "Aquaphor OSMO-50" (version 5) provides for the liquid to go through 5 stages. Purified water is supplied from the faucet, which is supplied. It has a classic design.
An important indicator of any reverse osmosis filter is its performance. The presented model can clean up to 190 l / day. If this is not enough for your family, it is recommended that you purchase a different system. For example, it can be "Aquaphor OSMO Crystal 50" (Spanish 5). It is able to filter out 375 liters of water per day. This is enough not only for a large family, but also for a medium-sized office team.
The advantage is the use in the design of universal flasks. This makes it easy to select the right cartridges and replace. You do not need to call a service representative for this.
Features of functioning
The package of delivery "Aquaphor OSMO-50" (version 5) includes several mandatory elements. To perform the installation correctly, you need to consider the main components and their features. So, the Filter has three pre-filters. Water passes through them before it reaches the membrane. This allows you to remove coarse impurities from the water and increase the life of the membrane.
The first pre-filter is a coarse polypropylene module from mechanical impurities. Its service life is 3 months.
The second cartridge "Aquaphor OSMO-50" (version 5) is a deep cleaning module. It is operated for 6 months. It is followed by a polypropylene cartridge for mechanical cleaning. It needs to be changed every 3 months.
Then water enters the membrane. This is a stage of deep cleaning. Membrane replacement should be done every 1.5-2 years. The fifth step that water passes through is air conditioning; for this, a 2 in 1 module is provided in the system that corrects taste and smell. It is changed once a year.
Customer reviews
Considering the reviews about "Aquaphor OSMO-50" (Spanish. 5), it should be noted that buyers leave mostly positive reviews about the presented model. If you have experience operating this reverse osmosis, share them in the comments to the article.
Buyers note that the quality of the outlet water is high. Even in areas with very contaminated liquids, almost all impurities can be eliminated. This has a positive effect on people's health and household appliances.
The advantage of the model is the presence of a mineralizer and an additional carbon filter for post-cleaning. Water has no odors. The mineralizer restores the normal taste of the liquid. The fact is that after passing through the membrane? water loses almost all the minerals that our body needs. Users note that the mineralizer that comes with the kit eliminates this drawback. Water has a pleasant taste, as its composition is as close to natural as possible.
Among the negative reviews about "Aquaphor OSMO-50" (Spanish. 5) it is worth noting the slow filtering process. However, for a family of 2-3 people, the presented cleaner is ideal. If more than 4 people live in the house, it is worthwhile to purchase a more productive system.
Also, some buyers do not like the design of the crane that comes with the kit. If necessary, it can be replaced by buying a suitable model in the appropriate store.
The total mass of buyers agree that the presented filter is of high quality water purification. It is easy to operate. There are no difficulties when installing or replacing cartridges. If they are replaced in a timely manner, the water quality will remain consistently high. The system will even cope with complex contaminants, such as hydrogen sulfide, nitrates, viruses and bacteria. Therefore, you can drink water, cook food on it and give it to children.
Expert Reviews
Considering the reviews about "Akvafor OSMO-50" (version 5), which are left by experts and specialists in the field of cleaning equipment, it can be noted that they call the model high-quality. This filter has more advantages than disadvantages. Therefore, it is in great demand.
Among the main advantages, experts call the versatility of the flasks and low cost. However, these are far from all the positive qualities of Aquaphor OSMO-50 (version 5). The presented model has a set of universal flasks, which greatly simplifies the system maintenance procedure. Also, a similar solution by the developers of the cleaner allowed to reduce operating costs.
Experts note that the advantage of the model is high-quality cleaning of chlorine contaminants of the liquid. For this, two carbon cartridges are provided in the system. It also helps eliminate all odors.
A positive quality of the filter is the disinfection of the liquid with silver ions. Also unique technology that is used in the presented model is Aqualen loading. It enhances the effectiveness of carbon cartridges.
Another undoubted advantage is the small size. Installation does not cause difficulties, since finding a place for installation is not difficult.
Among the shortcomings, experts call the lack of transparent flasks. This does not allow controlling the level of contamination of the cartridges of mechanical cleaning.
System installation
Before starting operation, it is necessary to study the instruction "Aquaphor OSMO-50" (version 5). If you perform the steps incorrectly during the installation process, this may cause a system malfunction. In this case, warranty service will not be provided.
To install the filter yourself, you need to shut off the water in the system. The kitchen faucet needs to be opened to relieve pressure. A connection node crashes into the water supply. The external thread must be wrapped with FUM tape.
Next, connect the JG handset. From under the sleeve of plastic you need to pull out the lock. The end of the tube must be moistened with water, and then inserted into the fitting to a depth of 2 cm. It should abut against the wall. The latch must be replaced.
Next, you need to go to the installation of a tap from which you can draw clean water. In the sink, you need to make a hole with a diameter of 1.2 cm. A seal is put on the tap thread, and then a washer and another stuffing box. The tap is inserted into the prepared hole. On the reverse side of the sink, a plastic washer, a counter washer and a metal nut are put on the thread.
The instruction "Aquaphor OSMO-50" (version 5) says that all actions must be performed in a certain sequence. You need to put a nut on the plastic bend. The conical sleeve must be inserted into the tube. The nut is screwed onto the valve sleeve.
A drainage clamp is installed in front of the siphon. For it you need to drill a hole with a diameter of 7 mm. On the inner side of the clamp you need to glue the gasket (the protective film is removed from it first). The holes in the fitting and drain line must be combined. Bolts are tightened further. They must be fixed evenly. In this case, both parts of the clamp will be parallel.
Replacing the membrane and cartridges
In addition to the installation "Aquaphor OSMO-50" (version 5)? it is necessary to consider the procedure for replacing the membrane. To do this, disconnect the JG tube from the fitting. Pull the locking tab and push the end of the sleeve out of plastic. This will allow you to extend the tube.
The membrane housing can be obtained from the seat. You need to grab it and pull it up with an effort. Next, the housing cover is unscrewed. The new membrane is removed from the package. It is installed in place of the old filter element. The wide seal ring should be on the threaded portion of the housing. The membrane is pressed with sufficient force so that it takes the correct position inside.
It is necessary to check the integrity of the seal, and then screw the cover onto the body. It is set to its original position.
Further, the end of the tube must be, as during installation, moistened with water and installed in the fitting until it stops. It is worth noting that when performing the initial installation of the system, you do not need to install cartridges or a membrane. All filter elements are already in place.
Replacement of cartridges "Aquaphor OSMO-50" (version 5) is even easier. In the kit there is a special key with which the flasks are unscrewed. First, the water is shut off, and the tap on the sink is opened. If you do not relieve pressure, unscrewing the flask will be difficult. Old cartridges are carefully removed from the seats. Filters must be thoroughly rinsed. You need to install new replacement cartridges. Further, the flasks easily twist, and the system can be operated again.
Flushing system
After installing or replacing the Aquaphor OSMO-50 filters (version 5), you need to flush the system. This will prevent carbon dust from entering the membrane. To do this, you also need to use the instructions that come with the kit. First, they shut off the water, open the faucet in the kitchen sink.
Then you need to disconnect the JG tube from the unit with pre-cartridges. The locking clamp for this is removed from the sleeve, press on the end and pull the tube. It must be disconnected from the storage tank, and then connected to the outlet fitting of the block with three cartridges.
The end of the tube is moistened with water and inserted into the seat socket until it stops. Liquid must be drained through the tap for purified water. The procedure is carried out for 15 minutes. To do this, open the previously closed flow of tap water. After this procedure, the valve is closed and the system is again closed.
The JG tube is disconnected from the unit with three pre-cartridges. She is again led to the storage tank. It is fixed with locking clamps. Then the membrane is installed. If you do not perform the above procedure, it will become clogged with coal dust. As a result, the throughput of the system and its cleaning properties will be minimal. The membrane will need to be changed.
System startup
It is important to properly run reverse osmosis. The inlet tap should be opened. You need to inspect the system for leaks. All joints, threaded connections are carefully inspected. If water droplets are visible, tighten the bolts and other joints more tightly. But you cannot be too zealous, as you can break the thread.
The handle of the tap for clean water must be opened. After some time, the filtered liquid will begin to drip. Then you need to wait 40 minutes. After that, the valve is closed. Wait approximately another 1.5 hours. During this time, the storage tank will fill up. The duration of this process depends on the characteristics of the membrane filter.
When the tank is full, you need to completely drain the liquid from it. When the flow of water weakens, you can close the tap. It is highly recommended not to drink water that the system would filter for the first and second time. The procedure is repeated again.
Only after the third filling of the tank with water can it be drunk and used for cooking.
During the first week, you need to periodically check the system for leaks. At the beginning of its work, reverse osmosis can filter water, which has a milky hue. It contains many air bubbles. They are forced out during operation from the system. Over time, the water will get its usual color, will become transparent. The presence of air does not reduce the quality of the purified liquid.
Replacing the carbon filter and mineralizer
To replace the carbon filter, which is installed after the membrane, water is shut off. By opening the tap for clean water, relieve pressure. The JG handset is disconnected. Then you can dismantle the post-filter by removing it from the holder. To do this, pull the cartridge up with an effort. The new post-filter is installed in the seat in the reverse order.
To replace the mineralizer perform the same actions. Water is shut off, the tube is disconnected from the cartridge, which requires replacement. The mineralizer must be pulled up with effort. A new cartridge is installed in its place. The steps for connecting all elements of the system are performed in the reverse order.