If you decide to install a toilet, then you can not do without cuffs and gaskets. These components are the elements that connect the pipes, the tank and the toilet. As a result, the compounds obtained are as tight as possible, so it is so important to choose the right products. After reviewing the information presented below, you can learn about the main types of gaskets, as well as receive recommendations on what to focus on when choosing them. After these components of the system are purchased, you have to install them to prevent leakage.
Appointment
If you believe that the gasket between the tank and the toilet is not such an important element, then you are mistaken. In order to make these two parts unified, a gasket is required, which ensures tightness. The product is ready to last even a few years, and after wear it must be replaced. Thanks to such an elastic band, the leakage problem will be completely absent. The main condition is that these components are suitable for the used types of plumbing fixtures, only in this way it will be possible to ensure a strong connection.
Main types
The gasket between the tank and the toilet can be installed by you yourself, but before that you must select this element of the system. Such cuffs are made of polyurethane, rubber or silicone. However, this classification is incomplete, since gaskets are also subdivided into forms, they can be:
- round;
- oval;
- in the form of a figure eight;
- cone-shaped;
- in the form of a truncated cone;
- curly, that is, trapezoidal.
Before choosing such a device, you must remember that it should be as elastic as possible, soft and elastic. The shape of the cuff for the tank must be correct. You should inspect the product, on its surface there should be no cracks and sag. Sometimes consumers are faced with the problem of dry pads. You do not need to purchase them, as they will not be able to carry out their tasks.
The shape of the cuffs can be different, so the worn part should be taken to the store. This will allow you to quickly pick up the product in all respects. Choosing it, you need to consider financial opportunities. If the model was produced abroad, then it can have a rather high cost, which is higher than domestic ones, but, as practice shows, they serve much longer. If you need a gasket between the tank and the toilet, then you can also be guided by the brand of the sanitary fixture, since manufacturers produce cuffs for their products that are original. It is worth acquiring just such a detail, as it fits perfectly.
Lavatory installation
The gasket between the tank and the toilet can be located on the shelf of the latter. This mount is one of the most popular; its main advantage is compactness. However, there is a drawback, which is expressed in low pressure. In order to get rid of sewage on the bowl, you need to use a large amount of water. To install this design, you can apply one of the following types of gaskets: round, guitar-shaped or laid on.
To replace, shut off and disconnect the water supply hose. The tank must be emptied by disconnecting it from the base. To do this, the through screws are loosened. If you have to work with the old model, then the screws can be made of metal, not polymer. Therefore, they can rust. Unscrewing them by force should not be, porcelain is fragile and may become cracked.
Specialist recommendations
If you purchased a gasket between the tank and the toilet, how to install this part, you should ask. The next step is to remove the seal, which usually remains on the bowl. It is replaced, and to improve the quality of sealing compounds on the base, you can apply a strip of silicone. This will fix the gasket and not allow it to shift during installation of the tank. Installation is possible by lining technology on the tank or by placing in a recess in the bowl.
Depending on which model of product you have in front of you, there may be an additional gasket for the toilet. Its function is not in sealing, but in depreciation when two elements come into contact. Given the fact that porcelain and earthenware are fragile materials, this gasket will eliminate contact between them, reducing the risk of damage.
For reference
A gasket between the drain tank and the toilet will not be needed if you have a monoblock in front of you, which is a single design of the drain tank and bowl. The use of such a device does not differ from classic models, but the cost will be higher than a conventional product.
Installing a gasket between a freestanding tank and toilet
This design has the advantage, which is expressed in the intensity of the pressure of the discharge water. Thanks to this, the bowl is cleaned efficiently, and much less liquid is left. The drain pipe is fixed to the device and can be sealed depending on the type of neck of the bowl. As a rule, there is an extension on it, which is used to tightly attach the cap cuff.
Behind the expansion, install a gasket. The contact surface of this element with the inside of the cuff can be treated with silicone. The second type of seal is transitional petal cuffs, which look like rubber products. The outside is slightly larger than the neck of the bowl. When assembling the elements, the contacting surfaces are lubricated with silicone.
The nuances of the work
The types of gaskets between the tank and the toilet have been discussed above, one of them you can buy in the store, capturing the worn part. If we consider in more detail the process after shutting off the water, then we need to drain the liquid from the drain tank, and then open it and disconnect the drain pipe. The siphon locknut is loosened, and then the feed pipe is disconnected, as is the overflow pipe. The screws are loosened, the cuff between the devices is removed. The place where it was located should be wiped dry and remove dirt and debris.
The gasket between the tank and the toilet is trapezoidal, like any other, is installed in its place, and then inserted into the screws. The tank is put in place and the fasteners are tightened. As soon as the plumbing device can be installed, it is necessary to wait about 2 hours until the silicone hardens, only then you can start using the device. If you install the toilet for the first time, then after installing it, the cuff is located on top of the fixing nut, after the screws you need to fix the tank. The gasket after installation should fit snugly to the surface of the tank and toilet bowl, only in this way it will be possible to ensure a tight connection.
Alternative solution
If you need a Santek gasket between the tank and the toilet, but you could not get it, and you need to deal with the leak, then temporarily the problem can be solved by purchasing rubber tape at the pharmacy. Its length should be equal to one meter, and width - 0.5 cm. Whereas the thickness can be equal to the limit of 1 to 2 mm.
The workpiece must be stretched, wrapped with a worn part, without removing it from the nozzles. The tape is reinforced with copper wire. If you have a Sanita toilet, the gasket between the tank and the toilet should be purchased from the same manufacturer, its cost will be approximately 400 rubles. However, if temporarily you decide to use a rubber tape, you can use a pencil to push it through. Using a screwdriver is not very convenient, since it has a handle.
Conclusion
Repairing and repairing a leak between the toilet and the tank cannot be called too complicated a process. The main thing in this case is to choose the right sealant and not be mistaken with the external and internal diameters of the products. Therefore, when buying replacement parts must be taken as an example of an old gasket.