Among the many household appliances, a refrigerator holds an honorable and special place in the kitchen. It is operated continuously and works around the clock. Doors open many times during the day. And of course, during use, as well as when moving or moving on the surface of household appliances, defects may appear. Which spoil not only the appearance of the device, but also the design of the kitchen as a whole. Next, we will look at how to fix a dent in the refrigerator that occurred during operation of the cooling device.
Sudden change in temperature
With minor damage, several methods can be used. Before applying one of them, it is necessary to thoroughly clean the damaged area with paper or fabric napkins. Next, consider how to fix a dent in the refrigerator by alternating opposite temperatures. To do this, use the included hairdryer. Point the device at the dented area and heat the area for about a minute, thereby expanding the metal. An average temperature value is sufficient to avoid overheating of the surface, which can disrupt the seal located in the inter-wall space.
After that, you will need prepared dry ice. To work with ice and not to get serious injuries in exposed skin, wear special protective gloves. It is also necessary to protect the metal surface of the refrigerator from possible scratches. Therefore, put a piece of ice in a soft rag from suede. Having placed the damage in the center, carefully begin to move the ice from the middle to the edges throughout the area for about a minute. Then stop and remove the rag. This is one of their simple and affordable ways to fix a dent in the refrigerator. The metal will return to its position, accompanying the movement with a characteristic click.
Suction Cup, or Mini Lift
Another way to fix a dent in a refrigerator is to use a device that creates a vacuum seal. Which, in turn, will stretch the defect, returning the metal to its original state. Before starting work, the surface of the refrigerator must be cleaned of dirt and wipe the place of damage with an alcohol solution in order to degrease.
Apply a special adhesive to the area and place a suction cup in the center. After the glue base has dried, a handle in the form of a rocker arm is put on the device. On both sides of the device are rubber gaskets that protect adjacent areas from damage. Then, with a special screw of the mini-elevator, by screwing, the metal succumbs to the suction of the suction cup and bends in the desired direction. After the dent was removed on the refrigerator, the appliance can be removed, the glue wiped off and the residual composition washed with water.
Hammer and trowel
There is a risky way to fix a dent on the refrigerator door with a rubber mallet. This method can be used by experienced craftsmen who are directly related to a similar type of work. Initially, it is necessary to degrease the metal, then heat the dented area with a hairdryer and press the trowel to the damaged surface. Next, tap with a hammer light strokes on the shoulder blade. In the process of vibration there will be a resonance of the surfaces, and the dent will assume the correct position.
Compressed air
Next, we’ll look at how to fix a dent on a refrigerator door using a can of compressed air. Most often they are used when cleaning computer parts and internal elements. It can be used to even out damage. When working, you need to raise the bottom of the can up and in this position, apply a little compressed air to the surface of the door.
During spraying, condensation is released in the cold state. Under its influence, the metal is compressed and takes its usual form. If this does not happen, then you can pre-heat the place with warm air from a hair dryer and repeat the procedure again. You may need to do the manipulation more than once.
Putty
One of the tricks that decide how to straighten a dent in the refrigerator is putty. To do this, paper with a fine emery surface needs to clean the damage zone. Then apply a primer on unevenness. After it dries, the dented area is putty. The main thing is to choose the right shade that matches the main color of the refrigerator. It is worth noting that not all surfaces lend themselves to this method. Even puttyed damaged areas remain visually visible, especially on glossy surfaces.
Important Tips
Using any of the above methods, basic precautions should be followed.
- Be sure to ventilate the room not only after work, but also in the process of straightening the dent. When using dry ice, it is important not to touch the pieces with bare hands - this can lead to injury and frostbite. Wear thick gloves that protect against contact with ice.
- A dent in the door makes you want to hit it on the other side. In no case do this and do not disassemble the door yourself. This will cause a violation in the cooling and tightness of the refrigerator.
- Do not use a conventional metal hammer as a shock. It can not only break the coating of varnish, which can no longer be fixed on its own, but also provoke new damage.
- If the dent is small, then you can simply decorate it using special stickers or magnets. You can place a family photo or a notebook with reminders.
Using our tips, you yourself will return your refrigerator to its original appearance and you can decorate its surface.