How to apply "bark beetle" plaster on the wall: step by step instructions, features and recommendations

A lot of materials are used today as the exterior decoration of buildings, among which are:

• decorative brick;
• composite;
• siding;
• ceramic tile;
• paint.

Along with all this, facade decorative stucco has been successfully used , the most common is the bark beetle, which gives the surface the appearance of wood eaten by the bark beetle.

Step-by-step instruction

Before applying the “bark beetle”, you should familiarize yourself with the technology of the work. The surface must be leveled, cement-sand plaster is used for this. It is best to use beacon profiles that are pre-installed. The walls will look much more aesthetically pleasing. Before applying decorative bark beetle plaster, beacons should be installed, between which a distance should be maintained that is less than the rule length by 15 cm. They are set according to the level, the last rails should be mounted first. Those in between can be installed along the threads that will be stretched between the extreme beacons from below and from above. A cement-sand mortar should be thrown into the resulting space, stretching it as a rule.

Features of surface preparation

On the screed will remain recesses and dents, which should be sealed with a grater. In order to speed up the work, you can use a half. Before applying "Bark beetle", a few hours after processing the wall at the initial level, it is necessary to wipe the base with a trowel or grater. In this case, it is necessary to act in circular motions, the plane should acquire an even appearance, this will save the base from defects. Additional grouting is performed the next day.

Specialist recommendations

If you have a question about how to apply “Bark beetle” on a wall, you should familiarize yourself with the methodology for carrying out the work. It involves leveling the surface with sand-cement plaster. Its application can be carried out in hot weather, while every day the surface is poured with water from a hose. This will guarantee uniform drying, the cement will not be covered with cracks, and if this happens, then the error can be wiped immediately.

Application of Bark beetle can be carried out on a wall insulated with extruded polystyrene foam or polystyrene. To do this, the insulation is fixed to the glue, the plaster mesh is laid, and the surface is leveled out small. The insulation must lie on the level, while not having to level the wall with plaster. Before using the Bark beetle plaster, it is necessary to allow the wall to dry, only this way you will prevent the formation of cracks on the finish. For example, sand-cement plaster will require three weeks or more.

Drawing "Bark beetle"

Thinking about how to apply the “bark beetle”, you should familiarize yourself with the technology, from it you can learn that plastering the walls should be done holistically. This indicates that at one time it is necessary to cover one wall, not counting the protrusions. The essence of this process is to ensure that each applied area remains fresh, not yet dry. The entire surface will look monolithic, there will be no drops and seams on it. The solution should be stirred with a mixer, you can use a slow-speed drill. Sometimes experts use a conventional drill, it should slow down.

Before applying the bark beetle, it must be prepared. First, water is poured, and then powder is poured. The optimal volume of water in the bucket should be 1/3. In order to achieve a high quality plaster mix, it should be mixed well until it turns into a mixture similar in consistency to mashed potatoes. The solution settles for 5 minutes, after which it must be broken again, only then it can be used.

The finish structure will depend on the manufacturer and the brand of the product. However, the master also influences these factors. For example, to form horizontal stripes, the solution must be applied in that direction. If it is necessary to obtain a vertical structure, then the movement of the hands should be directed from the bottom up.

When creating a particular structure, you can appreciate the importance of pre-decoration. The smoother the facade plaster, the clearer the “bark beetle” relief, because it is created thanks to the pebbles in the powder.

Layer decoration

If you are faced with the question of how to apply “bark beetle” plaster, then you should know that you can carry out these works in circular motions. After drying, the surface can be painted with an acrylic composition. Painting the plaster is not a matter of personal choice, it is recommended by the manufacturer, although the wall can stand unpainted for some time.

Features of the work

Quite often, the plaster described in the article is available in the form of a finished mixture, which does not imply the need for preliminary preparation. After the acquisition, you can immediately proceed to the application phase. For work, use a steel hard spatula. To protect adjacent surfaces, masking tape is glued to them along the outer perimeter. The plaster must be applied in accordance with the thickness of the layer, it should be the same as the diameter of the grain. If you are thinking about how to apply the bark beetle plaster, then you should pay attention to the fact that the mixture is stretched along the wall according to the same principle as putty.

It is important to achieve an effect in which small grooves appear on the fresh layer. This will indicate that you were able to achieve the optimal layer thickness. After that, a texture is created, for which it is necessary to perform circular motions of medium intensity on a fresh layer with a plastic grater. Sometimes stucco sticks to the grater plane , this can be considered normal. 15 minutes after application, the bark beetle should be treated with a plastic grater again, this time the pressure should be more impressive. By this time, the composition will slightly thicken and dry. Only after the first pass does the surface clean. This will form the final appearance and pattern.

Quite often, beginner home masters think about how to apply the bark beetle correctly. Experts advise: it is important not to overdo it, because with more approaches the wall will be smoother.

At the final stage of applying the mixture, all joints must be treated with a grater. If the joint is not jammed, you should not let it dry, because it will be visible on the finished wall. It is more convenient to apply the plaster on the surface together, one master will spray and stretch the mixture with a spatula, making the first mashing. The second master in 15 minutes will form the final look. As soon as the walls are plastered, masking tape can be removed. The protruding edge of the "bark beetle" is cut with an ordinary clerical knife.

Final work

Now you know how to apply the bark beetle to the facade. But it is important to familiarize yourself with the technology of the final works. They suggest conducting glazing. To do this, choose a high-quality acrylic varnish, which can be matte or glossy. Its preparation can be carried out so that the desired color is obtained. You can add nacre and shine to the varnish. For this, a certain technology is respected.

The plaster after application is left for a day, and before applying the varnish, the surface is primed so that the glaze does not cover the surface with spots. If you also have a question about how to apply “bark beetle” correctly, then you should take into account that these works are carried out using a steel spatula, which is convenient to use to remove excess varnish.

For reference

Sometimes people ask themselves whether it is possible to apply a bark beetle to a bark beetle. Experts give a definite negative answer. This is because the grooves form on an exceptionally smooth surface.

Conclusion

Now you know how to apply “bark beetle” on the wall, however, before starting work, you need to become familiar with the main varieties of this material. It can be designed for facades or interior work. On sale you can also find universal mixtures.