The Baby washing machine can be considered a real rarity. Today it can only be found in the families of older people. However, this belief is not entirely true. Similar models of household appliances are still found in some modern consumers. This is due to several factors. Among them, it should be noted the simplicity of the device and ease of operation.
There is no drum in the unit, as well as sophisticated electronics. This also suggests that complex damage with such a machine should not occur. Yes, and they can not be fatal. Usually, home craftsmen do the repair of such units on their own. If you are also faced with such a need, then you should familiarize yourself with the features of their elimination.
Disassembly
If you wondered how to disassemble the Baby washing machine, first you need to remove the cork from the hole in the back of the electric motor casing. The oblong hole of the impeller must be aligned with the hole in the casing. Through it, a screwdriver is inserted into the rotor of the engine. The activator is twisted.
Insert a key into the hole of the activator housing and unscrew the housing. This will disconnect the tank. Dismantling the Baby washing machine in the next step involves loosening six screws. Then you can remove the flange and unscrew the lock nut, as well as the rubber nut. They lock the switch. Now you can remove the washer and loosen the screws that tighten the halves of the casing. Underneath is an electric motor and other items of equipment.
Activator Problem Solving
Part of the problems is caused by a faulty activator in the machine. Leaks can occur due to improper connection of equipment or wear of o-rings and various rubber bands. But do not get ahead of yourself. It is important to begin to understand what an activator is.
This is a movable element, due to the rotation of which the washing takes place. Violation of mobility leads to a halt in the process. Sometimes a thermal relay trips and the machine simply shuts down. Before doing repairs, you should familiarize yourself with the main problems that are caused by the activator. You also need to understand how to resolve such problems.
So, if the tank is overloaded, then at startup the activator will not spin normally. He may stop altogether. The machine will start to buzz, and the solution will be to unload it. After this, you need to wait about 15 minutes and restart. Repair of the Baby washing machine may consist in the simple removal of threads and foreign objects, as well as rags from the shaft. It is part of the activator.
If the car started to hum, and then turned off, then the repair consists in cleaning the shaft. Sometimes it happens that the described node is skewed. It continues to spin, but the laundry after washing is often badly wrinkled or even torn.
When the activator touches the walls of the tank, you will hear a strong hum. The machine may turn off for no apparent reason. The solution is to deploy the device and remove the plug. The activator is unscrewed, and after the thread is cleaned. The assembly is put back in place until it stops. After that, the device should work properly.
Leakage Repair
Repair of the Baby washing machine may be required during a leak. This happens quite often. Do not ignore the problem by installing the appliance in a bathtub. This approach can be dangerous, because leakage from a hose or tank damages the electronics. A short circuit occurs, and the user may receive an electric shock. Leaking the leak without attention is not worth it.
First, check the case. A large o-ring or flange assembly may be damaged. In order to determine the location of the leak, you must partially disassemble the structure. Repair of the Baby washing machine in this case is expressed in the dismantling of the activator and the unscrewing of its body.
A large gum is inspected for damage. It is also called a large o-ring. If defects were detected, then the part changes to a similar one. When the elastic is intact, the casing and the electric drive should be disconnected from the tank.
Six screws are removed, the casing is disassembled, and then the flange assembly is removed. It should be disassembled and photograph the location of the parts, after which you can remove the rubber sleeve. It must be inspected for damage. The small o-ring should also not be ignored. If damage has been detected on one of the parts, replace them.
Alternative Leakage Cause
Repair of the Malyutka washing machine may be required due to a leak caused by a small snap ring. It is part of the flange assembly. If the ring does not compress the cuff tightly enough, it should be replaced with a tight one or bent. But this does not guarantee that the leak does not recur over time.
Leakage control when fittings or hoses are the cause
It is easier to detect and repair leaking fittings or hoses. The first is held by a nut, which must be unscrewed and the sleeve removed. The gasket is pulled out in the next step.
If even the smallest damage has been noticed, replace the part. The hose can get damaged, but over time, low-quality products dry up, crack, and become unusable. This leads to the fact that they begin to leak water. The only way out of the situation is to replace the unit.
Engine Troubleshooting
Faults and repairs of the Baby washing machine are quite often very simple. This is due to the design features of the described model. You may find that the engine starts to junk. Loss of contact of one of the engine windings may indicate this. Rewinding is not economically feasible. Even if you do it yourself, spend a lot of time.
Buying a motor or car
It’s easier to change the motor to a similar one or purchase a new Baby washing machine. The latter option is more optimal, because the new engine is costly, as is the described equipment. But if you still decide to do the repair of the Baby washing machine with your own hands, you should know that the equipment provides an asynchronous single-phase motor with two windings.
Stuffing box replacement
The need for replacing the seal can also indicate leakage. This piece of equipment is located at the junction of the tank and the engine. On the opposite side there are holes on the engine. Insert a screwdriver there and unscrew the activator. It has blades and is wound on a threaded shaft. First you need to see which way it is spinning. This will remove the assembly.
Knowing the design features, you will be able to independently repair the Baby washing machine. Gland replacement is no exception. Given the device of the described device, it can be noted that the models can have different directions of rotation of the activator. There may be left or right thread on the shaft. When replacing the stuffing box, the activator is also usually changed. Indeed, sometimes it is impossible to cope with a problem only by replacing the oil seal. This is due to the fact that at the activator the thread breaks the sleeve into which the shaft is screwed.