When installing a heating system, pipes in a private house or apartment are stretched across all rooms. And of course, such beauty designs do not add to the interior of the premises. There are several ways to mask heating pipes. And all of them are quite simple to implement.
What techniques can be used
So, let's see how to hide heating pipes in a private house or apartment on their own. You can hide highways in residential premises, for example, in the following ways:
lay them inside walls, floors or ceilings;
close the pipes with homemade boxes;
hide designs under decorative purchased items;
to lay communications under false walls or a plasterboard ceiling.
In some cases, pipes can simply be painted or even applied to patterns or patterns.
Choose a way to mask highways, depending on the features of the layout of the premises, the design of the heating system, the design of the premises, the financial capabilities of the owners of the house or apartment.
Laying communications in building structures: gating
Installation inside walls, floors or ceilings is a good answer to the question of how to hide heating pipes in a private house. This method is easiest to implement even at the stage of construction of the building. But if you want, you can lay pipes inside the walls or floors and already in the finished house.
It is allowed to extend heating lines inside both panel board and concrete or brick building envelopes. This technology is also a good answer to the question of how to hide heating pipes in a private house from aerated concrete.
In the stone walls, no matter what kind of material they were erected, highways stretch in the gates. So called grooves made with a grinder in concrete or brick. In this case, the work to prepare for the layout of highways will be as follows:
markings are made on the wall, concrete floor or ceiling using a level or level;
with the help of a grinder, slots are made in the structures along the entire length of the highway;
a chisel or perforator knocks out a strob.
The marking with this method of masking the pipes is done in accordance with the width of the highway plus the margin for its insulation. The depth of the slotted groove should be such that the pipes together with the insulator are recessed into it with respect to the plane of the wall, ceiling or floor.
Stacking pipes
Highways before laying in the hollowed-out grooves are wrapped with foil-coated heat-insulating material. This will allow subsequently to operate the heating system with maximum efficiency.
Next, the pipes are laid in the shtroba and mounted in it using brackets. Then the groove with the highway is sealed with concrete mix. At the final stage, the wall, floor or ceiling is finished.
What rules should be followed
When ditching the wall with this method of masking, places for fittings should be provided. In the future, those areas in which tees, couplings, corners, etc. are located, are not sealed with concrete, but simply covered with special decorative windows. The same elements are installed at the pipe joints inside the wall.
It is not possible to use such masking technology for all types of heating mains. It is suitable, for example, for pipes:
Popular metal-plastic lines can be mounted inside the building envelope only if press fittings were not used for connecting them. Polypropylene pipes do not fit inside the walls.
Before embarking on embedding concrete with a pipe with pipes, the heating system must be checked for leaks. Repair of highways already after laying in enclosing structures, even with windows, is quite difficult.
In the event that the system has been installed in the house for a long time, before hiding it in the walls or floor, experts advise replacing the old pipes with new ones. This is especially true for steel lines.
Laying inside wooden structures
The answer to the question of how to hide heating pipes in a private house if its walls were erected using racks and boards is a rather simple technology. It is easy to stretch the trunk inside the wooden floors or floors. The only thing - in this case, laying can be performed only at the stage of building construction.
In the floor of the heating main, it is best to disguise if the project has planned their lower wiring. Radiators using this technology are mounted saddle-mounted. That is, pipes in the process of tapping are attached to their lower nozzles.
When arranging the floor in this case, holes of such a diameter are made in the logs so that highways with a heat insulator can pass through them. Next, the heating system itself is mounted, and then the floor boards are already filled.
Using approximately the same technology, pipes extend in shield walls, as well as in interfloor ceilings. In this case, the holes are made in the uprights of the frame and beams, respectively.
Where to hide heating pipes in a private house: purchased boxes
When using factory decorative designs, it is very easy to hide heating pipes. Such elements are usually made of plastic and are installed using several fasteners, according to the instructions from the manufacturer.
With the lower wiring of highways, a decorative box of a special design made under the plinth is often used for masking. How to hide heating pipes in a private house under such a design? The answer to this question is simple. Skirting boards of this variety are mounted in the same way as ordinary ones. They differ from the latter only in size.
Using GCR
Ready-made decorative boxes are mounted very easily, but such designs are not cheap. Therefore, many owners of country houses and apartments prefer to hide heating pipes under improvised plasterboard boxes.
In this case, the installation of the masking structure is as follows:
The frame for the box can be made of timber or a special metal profile. In any case, its elements are attached to the walls using self-tapping screws. Drywall is pre-cut to the size of the box. Further, the sheets are attached to the frame also using self-tapping screws in increments of 25 cm.
How the pipes look under such a box can be seen below in the photo. How to hide heating pipes in a private house under drywall, in this way, is understandable. But instead of gypsum fiberboard, for cladding the box, you can use MDF or plywood. The choice of material in this case depends on the features of the interior design of the room. If desired, gypsum plasterboard can be plastered or, for example, glued with wallpaper.
With your own hands, to mask the heating mains, it will be easy to make a plastic construction. This material is also a good answer to the question of how to hide heating pipes in a private house. Plastic panels are inexpensive and resistant to high humidity.
In this case, the frame of the metal profile is also pre-assembled. Further, it is simply sheathed with suitably cut plastic panels.
How to hide heating pipes in a private house: disguise under false structures
This method is used if a large number of pipes have to be pulled around the room. The box in this case will most likely be impractical. False walls and plasterboard ceilings are made. When using this technology, a frame made of timber or a metal profile is also pre-mounted on the base. Next, the pipe is laid. At the final stage, the walls or ceiling are sheathed with plasterboard.
Masking of highways when using this method is relatively inexpensive. Rooms with false walls and ceilings look very aesthetically pleasing. However, such designs have one rather serious drawback. They reduce the useful area of the room.
Disguise in the bath and sauna
In these rooms, characterized by high humidity, you can hide the heating mains:
- under a plastic box;
- using special blinds.
Drywall is also a good answer to the question of how to hide heating pipes in a private house in the bathroom or sauna. However, in this case, for the skin of the frame, it is necessary to use, of course, special moisture-resistant GCR.
Pipe painting
So, we found out how to hide the heating pipes in a private house under drywall, plastic or by shtrobleni walls. But all these methods, despite the technological simplicity, are still quite laborious. They are mainly suitable only for living rooms. In utility rooms, pipes are usually masked nevertheless simply by painting to the color of the walls. Thus, it is supposed to use exclusively coatings resistant to elevated temperature and humidity in order to process highways.
Plastic pipes are usually initially white and harmonize well with most other shades. Such structures, of course, are usually not stained. Use this method of disguise only for steel lines. For coloring such pipes of the heating system, for example, alkyd quick-drying or acrylic enamel can be used. The heating system pipes are painted as follows:
pipes are cleaned of rust and exfoliated old paint;
they process the surface of highways with sandpaper and wipe them with white spirit;
process pipes with a corrosion-resistant primer;
apply on the highway paint, if necessary, in two layers.
How to mask radiators
How to hide heating pipes in a private house on the floor, walls or behind the boxes, in this way, it is clear. But masking such elements, owners of suburban residential buildings usually additionally hide radiators. Heating system batteries can be closed, for example:
Of course, heating radiators, so that they fit better into the interior, you can paint. When disguising batteries, it is only important to try not to reduce their heat transfer.