Have you been facing the problems of central heating or hot water for a long time? These issues can be solved by installing a gas boiler.
Central heating problems
The solution may be a single-circuit or double-circuit boiler. The first variety is able to provide a heating process. With the help of a dual-circuit device, it is possible to provide not only space heating, but also heating of the coolant for solving domestic problems. If you decide to purchase a double-circuit gas boiler "Beretta", then it is worth remembering that installing it will be quite a troublesome and time-consuming process.
Reviews on the rules for installing a gas boiler
Many people like Beretta brand products. The gas boiler of this manufacturer can be purchased at an affordable cost. Before you start installing the device in a private house, you will need to prepare some documentation, as well as carry out certain actions. Thus, a contract for the supply of gas to the developer, an installation project will be needed. Specifications must be agreed with the representative of the gas service.
Project documentation is most often developed by specialists of institutes who work under the appropriate license. Gas equipment should be installed by professionals from installation organizations.
According to users, the engineer of the district organization must visit the facility in order to check whether the gas is correctly supplied to the kitchen and to the furnace, and whether the requirements are met. Quite often recently, consumers have chosen Beretta brand products, and a gas boiler is no exception.
After the specialist is convinced that all the standards are met, he will issue a conclusion, on its basis it will be possible to open the valve, which leads to the equipment. The heating system must be pressure tested to P = 1.8 atm.
It will be important to dehydrate the heating system. Experienced users emphasize that the connections must be checked for leaks, it is necessary to install a voltage stabilizer for the equipment and a source that will be responsible for uninterrupted power. It is worth remembering that in no case should you add antifreeze to the heating medium.
Reviews on the rules of the design of the boiler room
When Beretta wall-mounted gas boilers are purchased, they must be installed in rooms to which certain requirements are imposed. When installing the boiler in a private single-family house, the boiler room or furnace can be located on any floor, including on the basement, on the roof, in the attic or in the basement. The restriction applies only to residential premises, as well as to the bathroom and the bathroom, where it is prohibited to place the boiler. Consumers emphasize that it is important to determine the volume of the boiler room, taking into account the thermal capacity of the equipment, the capacity of water heaters, as well as flow tanks.
For reference
If you decide to install a Beretta gas boiler, consider that it is important to take into account some factors when installing it. So, if the device has a closed combustion chamber, then the volume of the boiler room is not standardized. In this case, it is not necessary to have a window. For the removal and supply of oxygen, it is important to ensure the flow of air in the required volume.
Thus, if you installed a boiler with a capacity of 23.3 kilowatts, the gas will burn in the amount of 2.5 cubic meters per hour. In order to ensure complete combustion of this volume, you need 30 cubic meters of air per hour. If you do not guarantee a sufficient supply of air, then the gas will not burn out completely, as a result, the harmful substance will begin to concentrate, its inhalation can negatively affect human health. If you inhale carbon monoxide for only 15 minutes, death may occur. Oxygen must penetrate not only from the outside, but also from other rooms of the house. This can be ensured by the presence of a gap that will be located between the door and the floor surface. It is also recommended that the grille be installed at the bottom of the door.
Specialist advice
The Beretta gas boiler should be installed on the floor with a ten centimeter retreat from the wall, which should be made of non-combustible material. If there are no such surfaces, then you can install special protection, which will be made of refractory material.
Installation Instructions
If the listed requirements are not met, the gas service will not allow connecting the boiler to the central highway. However, the need to comply with these requirements is not dictated by the bureaucracy, but by experience, as well as fire safety. The restrictions apply not only to equipment and installation work, but also to the room where the boiler is supposed to be installed.
It must be remembered that the area of the boiler room should be 4 square meters or more, and the ceilings should be at least 2.5 meters. When installing the door, keep in mind that its width should be 80 cm or more. If you decide to prefer the Beretta manufacturer, the gas boiler of this company will meet all safety requirements, however, it is important to comply with the established rules. They suggest the need for natural lighting equipment through a window opening. For 10 square meters of one room should be 0.3 meters square window opening. It is very important to organize intensive ventilation, because gas combustion is ensured by the principle of fresh air flow. To ensure the supply of external air, it is necessary to ensure the presence of an opening of 8 centimeters square per 1 kilowatt of power of the device.
Additional instructions
The gas boiler "Beretta", reviews of which are only positive, should be connected to the pipes of the gas pipeline, which are made exclusively of metal. The use of flexible hoses is permissible only for connecting individual consumers. The chimney must have a cross section that corresponds to the power parameters of the unit. If it is equal to 30 kilowatts, then the diameter of the chimney should be 130 millimeters. With increasing power to 40 kilowatts, the diameter increases to 170 millimeters. There is no way to allow the cross-sectional area to be smaller than the cross-sectional area of the hole for connecting this element.
If you decide to choose a Beretta gas boiler, the installation instructions for which are presented in the article, it is important to remember that the upper end of the chimney should be raised 0.5 meters above the ridge. This value is the minimum.
What else to look for
Be sure to provide a gas analyzer that needs to be located in the boiler room. With this appliance you can prevent a gas leak. The device must be equipped with an electric valve. The latter is designed to shut off the gas supply if necessary.
The Beretta manufacturer, whose gas boiler you can get at specialized points of sale, indicates the possibility of equipment location in the basement of an exclusively single-family house. As for multi-story buildings, the installation of the device in the basement is prohibited.