Some country cooperatives do not provide for the installation between sections of fences made of slate or any other similar material, since such designs obscure small areas. At the same time, a fence made of welded galvanized mesh becomes an excellent outlet. It will not prevent the ultraviolet from entering the area, it will not impede the natural circulation of air and can be erected by any summer resident.
Training
The chain-link is an inexpensive material that is ready to last quite a long time. As its additional advantage, it is possible to use it as a support for climbing plants. This grid was invented back in the late 19th century, but is still widely used to this day. Every consumer is able to purchase it.
To create a fence, in addition to the mesh, reinforcing bars, thick wire, support posts and cable should be prepared. When choosing a grid, you should pay attention to the size of the cells. The smaller it is, the mesh will be more expensive, but also stronger. If the mentioned parameter is equal to the limit from 40 to 50 mm, and the width of the roll is 1.5 m, then this material will be an excellent solution for creating a fence of a summer cottage.
Tension fence
The fence made of welded galvanized wire mesh can be tensioned. This method of its manufacture is the simplest. After all, the material will have to be pulled between the posts, which can be made of the following materials:
The number of supports will depend on the step between them and the length of the fence. The best distance is a parameter of 2.5 m. Pipes can be used as poles, however, they should not be damaged by corrosion. On sale today you can find ready-made poles that have hooks and a painted surface. Wooden supports must be treated with a protective compound before installation.
Concrete poles act as an alternative solution , to them the grid is fixed with a clamp or wire. The height of the posts must be calculated. If the clearance between the ground and the fence is from 5 to 10 cm, then the underground part of the support and the width of the grid should be added to this parameter. The load on the corner posts will be greater, so you need to position them deeper than the rest. Therefore, their length should be greater than the length of ordinary columns by 20 cm.
When making a fence made of welded galvanized wire mesh, you must concrete the bases of the supports to increase strength. The posts will be a frame structure. After installing them, you can begin to fix the grid. Once the concrete has hardened, hooks are fixed to the posts or welded if the post is metal. In the role of material for fasteners, you should use:
- wire;
- nails
- rod;
- wood screws.
You can apply any other material that bends into hooks. At the same time, the roll is straightened and installed at the corner support, the grid must be hung on hooks.
Recommendations for work
The roll must be rewound one span to reach the next pillar. The rod is passed a little further than the place where the grid will connect to the column. The master should hold the rod and pull the net. If the rod is not used, then the mesh may not be stretched evenly.
It is better to carry out these works, enlisting the help of another person. He will hold the grid at the bottom edge, while the other master at the top. At the next stage, reinforcement is threaded into the grid, 5 cm must be retreated at the edges. When installing a fence from a welded galvanized grid, it is necessary to weld horizontal rods or attach to poles.
Without using rods, over time you will come across the fact that the grid will sag. When technology is respected, rods are used to maintain tension. The mesh should be pulled further according to the principle described above, fixing and stretching the rod or wire. On this we can assume that the fence is almost ready. Hooks are bent on poles, the last of which are painted. The wire antenna must be wound down to reduce the risk of injury. The wire is usually threaded through the upper edge of a row of cells; sticking edges should be wrapped around it.
Sectional fence
To build a sectional fence, you will need sections where the mesh will be installed. At the first stage, you should use a technology that is similar to the above. To do this, the territory is marked, and after the posts are installed.
Installation of the fence from the grid will involve the use of a corner whose dimensions are 40 x 5 mm. These elements will be needed to make the frame. Its length is determined taking into account the distance between the columns, from this value it is necessary to subtract 15 cm. The same should be subtracted from the height of the column above the soil level. This will allow you to get the width of the frame.
Corners need to be welded into rectangular structures. The size of the sections is made taking into account the size of the mesh, which varies from 1.5 to 2 m. The welded galvanized wire mesh in rolls can be cut with an angle grinder if necessary.
Methodology
At the next stage, metal strips are welded to the posts. They should be placed horizontally. Their length can be from 15 to 25 cm. As for the width and section, they are 5 cm and 5 mm, respectively. With a 20 cm deviation from the edge of the column, it is necessary to install a section between two supports. For this, welding is used. At the next stage, you can begin to stain the fence.
Fence cost
Quite often summer residents and owners of territories within the city wonder about how much a galvanized wire fence costs. If the width of the material is 1.5 m, then you will have to pay 310 rubles for such a fence. per linear meter. Using a grid with a width of 1.8 m, specialists charge 390 rubles for their services. per linear meter.
A broach of reinforcement will cost the consumer 40 rubles. per linear meter. You may also be interested in the question of how much the fence costs. If its length is 50 m or more, then for a running meter you will have to pay 355 rubles. This price is true for designs in which the fittings are installed in one row. The width of the net is 1.5 m. This parameter will be equivalent to the height of the fence. If it increases to 1.8 m, then the cost will rise to 415 rubles. The price includes metal supports, pulling fittings in one row, galvanized wire mesh and installation work.
Grid cost
If you yourself decide to do the installation of the fence, then you can ask about the cost of the grid. If the diameter of the wire used is 1.2 mm, and the cell size is 10 x 10 mm, then you will have to pay 455 rubles per square meter of material. The price per roll will be 6825 rubles.
The galvanized wire mesh, whose cell is 20 x 20 mm, will cost the consumer 234 rubles. per square meter. Furthermore, the diameter of the wire used is 1 mm. But the price per roll will be equal to 7020 rubles. As the cell size increases to 25 x 25 mm, the cost rises to 416 rubles. per square meter. The diameter of the wire is 2 mm, and the price per roll will be 12,480 rubles. Welded galvanized wire mesh 50x50 mm will cost the consumer 312 rubles. per square meter, while the price of a roll will be 7020 rubles, and the diameter of the wire will be 2.5 mm.
Conclusion
Welded galvanized wire mesh in rolls will be an excellent material for the manufacture of the fence. It is easy to cut, it is quite simple to pull it between the supporting posts, in addition, it is durable. And in some cases, the grid is the only right decision when it is necessary to protect the site, but it is required to provide access to sunlight.