The purpose of the creation of bulk floors was to reduce the duration of work and labor costs, which is accompanied by outdated decoration and leveling schemes.
Solution of the problem
Both tasks are perfectly solved by a self-leveling compound, with the help of which it is possible to create a perfectly smooth, durable, monolithic surface with no seams in the shortest time. Among the advantages, it is worth highlighting the possibility of self-pouring without professional help. Today in the market you can find the quick-hardening bulk floor of "Prospectors", which can be thick or finish.
Characteristics of a thin finish bulk floor brand "Prospectors"
This finishing composition is used to level the floors, which may have different characteristics. At the same time, different humidity can be stored in the room. It is permissible to lay parquet, tile, linoleum or other materials on the surface. Using this composition, you can form a layer with a thickness of 1 to 20 mm. After 28 days, the quick-hardening bulk floor of “Prospectors” will reach a pressure resistance of 20 MPa. The activity of the solution will remain for 40 minutes, so care should be taken to develop it during this time. Complete drying of the surface will occur after 4 hours, which can be considered a big plus. On one square meter of the surface it will take 16 kg of dry composition, this is true if you will form a centimeter layer. On a 25 kg bag, add about 6 liters of water.
Application Features
Finishing quick-hardening bulk floor "Prospectors" should be applied and evenly distributed over the surface. Use a needle roller to remove air jams. Since the material is made on the basis of cement, polymer additives and fillers, cement, anhydride, and also gypsum bases can serve as a rough base. However, their strength should not be less than 150 kg / m 2 .
The base should be cleaned of dirt and dust. Otherwise, the mixture may not adhere to the surface so firmly. Before starting work, all irregularities should be removed by filling them with special mixtures. About 6 liters of water must be poured into the container, into which one bag of dry fraction is poured. Using a construction mixer, mix the composition for 4 minutes until you can get an average mass without lumps. The mixture is left to stand for 3 minutes and mixed again. In order to exclude unexpected results, add as much water as recommended by the manufacturer.
Reviews about the thick bulk field of the brand "Prospectors"
According to customers, the quick-hardening bulk floor of “Prospectors” (25 kg) is also offered for sale in the form of a mixture, which is used to form a rough thick layer. Concrete floors can be used as the main surface. Users emphasize that the areas of application are repair and construction of utility residential premises. According to users, the thickness of the coating layer can reach 100 mm. Use this composition in tandem with a warm floor system. It is noteworthy that the quick-hardening floor is non-shrinking and suitable for both indoor and outdoor use. Bulk floor quick-hardening "Prospectors", the technical characteristics of which will be important to you if you plan to use it, has the qualities of frost resistance. For internal use, the conditions should differ in normal humidity. Application can be made both mechanized and manual. As users emphasize, linoleum, piece parquet, natural stone, carpet, laminate or floor tiles can be used as a subsequent finish.
The main characteristics of the thick floor "Prospectors"
This mixture has a gray color. The recommended local layer thickness is 10 mm, but the minimum total layer thickness is 30 mm. About 25 kg of water should be added to 25 kg of the mixture, as in the case described above. The minimum volume is 5 liters. This indicates that for one kilogram you need about 0.24 liters. The time of use remains the same, while maintaining the temperature within + 23 °. Bulk floor quick-hardening "Prospectors", the consumption of which is mentioned in the article, can be used after two days. It is important to note that the manufacturer indicates the recommended temperature for the work, it can be in the range from +5 to + 30 °. If the floor is laid outside the building, it will be able to withstand about 35 cycles of freezing and thawing. With a layer thickness of 10 mm per 1 m2 of surface, approximately 17 kg of dry composition will be required.
Surface preparation
The quick-hardening bulk floor "Prospectors" (25 kg bag) can be purchased by you to level the surfaces. Moreover, to obtain a positive result, it is necessary to properly prepare the basis. It should be cleaned of oil stains, dust and other substances that could reduce the adhesion to the surface. If necessary, you can apply a universal primer of the same brand. Leave the surface after this for one hour until completely dry.
If you have to work with highly absorbent substrates, then the primer can be carried out in two layers. A damper tape should be fixed along the walls around the perimeter of the room and around the columns, as well as other protruding elements . In order for the quick-hardening bulk floor of Prospectors to lay down in an even layer, it is necessary to install beacons. The correctness of their location is checked by level or construction level.
Application Features
The solution should be distributed using a pump or manually, if necessary, leveling should be carried out by rule or rail. To eliminate air bubbles, it is recommended to walk along the surface with a special roller, this must be done immediately after pouring each portion. Quick-hardening bulk floor “Prospectors”, reviews of which are the most positive, can be used to equip the screed, while the thickness of the fill on the separation layer should be 30 mm. In the first 48 hours after completion of the work, drafts and UV rays on the surface should be excluded. If you plan to use a parquet board, plywood or piece parquet, then you must install these coatings after 4 weeks, which will depend on the drying conditions. If you use a thick quick-hardening bulk floor "Prospectors" (25 kg) for subsequent tile laying, then installation work should be carried out after 7 days.