Fairings on the "Gazelle" is not just an improvement in the exterior, but also a real opportunity to increase the aerodynamic performance of the car and the exchange rate stability along with fuel economy at a low cost and without high labor costs. The effect of this conversion is especially noticeable at speeds above 50 km / h. Even the simplest spoilers noticeably smooth out the negative impact of the headwind.
General information
The installation of fairings on the Gazelle is a kind of fashion tribute to various body kits, which are widely popular for tuning sports and racing cars. Some conservative users consider this design just a decorative element for decoration, and not a practical detail that can improve the parameters of the machine. However, practice shows that the spoiler on small trucks significantly improves the running and technical characteristics of the vehicle.
Demand in the automotive market for this type of body kit is huge. Spoilers are purchased by both truckers and drivers whose route passes within the city. The manufacturing material for the devices under consideration is mainly fabric samples or fiberglass. Polyester resins are used to bond the components together . Protection of the polymer product from weather and mechanical influences provides a number of special additives.
Where to start installing the fairing on the Gazelle?
This element is preferably mounted on the roof of the car. Perform work in compliance with certain conditions. Firstly, the supports must be fixed behind the roof amplifiers, otherwise the design may not withstand the load at high speed with a strong headwind. Secondly, it is desirable to place the spoiler as close to the edge as possible in order to reduce the entry into the rarefaction zone.
Before you begin installing the fairing on the Gazelle, you need to mark the future placement of the supports. Work is recommended to be carried out together. The assistant must hold the spoiler at the intended installation location. At the same time, it is necessary to measure the distance between the supports and from them to the edges of the roof. Choose the optimal position so that the element is parallel to the edges of the vehicle.
At the next stage, before mounting the part, repeated measurements should be made. This is due to the fact that the slightest inaccuracy and violation of the design will lead to a loss of aerodynamic performance and the expected effect of the part is transformed into a disadvantage. As a result, you have to redo the whole process.
Installation instructions
The fairing on the Gazelle Next is mounted in stages, in the following sequence:
- According to the marked marks, places for fastenings are drilled.
- The drill must be held strictly vertically down, it is desirable to drill the nests on both sides.
- The component supports are fixed with bolts. To reduce the load and expand the mounting area, use a wide flat washer.
- The correct length of the screws and the quality of the nuts should be chosen in such a way that they provide optimal tightening torque with an additional washer. During the installation of the spoiler, a slight deflection of the roof base may be observed.
- After completing the installation work, it remains to conduct several test runs and compare the results “before” and “after”.
The method without drilling
An alternative option for installing a fairing on the Gazelle-Business is to install it without drilling. In this case, the spoiler sits on the sealant or double-sided tape. This method is less reliable and does not provide the most durable fixation. Ideally, it is advisable to use both methods in combination: bolt the element, treating the seats with adhesive.
If possible, try to adjust the angle of attack. For example, to enhance the clamping action in corners, the fairing should have an increased angle of attack, and a reduced rate provides a quick acceleration of the vehicle. As a result, a correctly tuned spoiler optimizes the aerodynamic properties of the car and improves the dynamics of acceleration.
Pros and cons
Among the advantages of fairings on the "Gazelle" note the following points:
- Protection of the ventilation system against stones and dirt.
- Fuel economy by reducing the impact of headwinds and improving the aerodynamic parameters of cars. In percentage terms, this figure reaches 5-6%, which is not so small for commercial vehicles.
- Improving vehicle dynamics, including traction and acceleration.
Minuses:
- The installation of some modifications requires the drilling of additional holes, which, if the anti-corrosion treatment is not sufficient, will corrode during operation.
- The cost of some spoilers reaches 8-10 thousand rubles, for installation - another 5000. Therefore, the payback of the element will take a long period.
Helpful information
To install the fairing on the "Gazelle-farmer" you will need a set of tools:
- Ruler or tape measure.
- White Spirit.
- Building level.
- Drill with a set of drills.
- The tool against corrosion.
- Protective metal mesh.
During the first thousand kilometers after installing the spoiler, you must regularly check the element for leaks. Installation of a fairing in a specialized workshop will cost at least five thousand rubles. Therefore, having elementary skills in installation work, it is more expedient to perform this operation on your own.
Testing
Below are the comparative characteristics before installing the spoiler on the Gazelle and after installing the fairing (in brackets):
- Acceleration to 100 kilometers - 59.9 seconds (45.8).
- Fuel consumption at a speed of 60 km / h - 11.1 liters (10.3).
- Improved dynamics allows less frequent use of the gear shift.
As a result, it can be noted that the installation of the fairing really improves some parameters of the car. The numbers may seem insignificant, however, if you take into account the commercial purpose of the vehicle and multiply all this by the long-term use of the element, the savings are not in doubt.